Throttle quadrant

[JDA_BTR]

I really like vernier prop and mixture controls. I've never used a throttle quadrant. I've read all the posts I can find about the left side console, verniers, and the throttle quadrant.

If I want to have a lock for the throttle, and a second for the prop/mix this most expensive option is available:

DJM MFG: 3 Lever Curved Top Side Mount Formation, Three Lever Quadrants, SMCT3L-Formation

www.djmmfg.com

If I want a vernier setup for prop/mixture and a quadrant for throttle, this set of posts has good info:

RV-8 throttle quadrant friction imbalance

Hard to come up for a title for this. However, my prop control is very easy to move and requires the singular quadrant friction lock to be very tight to prevent it advancing to fine pitch. The throttle and mixture are similar to each other but require far less friction lock to stay put. When I...

vansairforce.net

So my questions are these:
1. With the verniers, is the hand position way forward and a pain to deal with, or not a big deal?
2. With the dual-lock quadrant, is any modification to the left panel needed, or is a drop-in?
3. With the single throttle quadrant, which is best and fits in without modification?

I like the pictures that have switches on that left side panel too, which I hadn't thought about before seeing them.

 

[michjor]

I think there are 2 considerations 1) individual friction locks for each control (MP, RPM, MIXTURE) and 2) ergonomics of using the quadrant versus verniers.
I have tried both and and did not like the quadrant, so opted for the way I like flying in an Extra 300 where you set RPM and Mixture on vernier controls and just work the throttle.
I modded my quadrant to this kind of prototype in my RV-8. (see photo attached)
The other big decision you need to make is the control CABLES. If you go with the Vans ones, they are made for marine boats, get very sticky after 100 hours, most need replacing after 200 hours and make the quadrant more difficult to use. I swapped my cables out for McFarlane and it made a world of difference to the ease of use and accuracy of the controls themselves.

Aircraft spruce has 2 types of quadrants- https://www.aircraftspruce.com/categories/aircraft_parts/ap/menus/ap/controls_vans.html

 

[fl-mike]

I really like vernier prop and mixture controls. I've never used a throttle quadrant. I've read all the posts I can find about the left side console, verniers, and the throttle quadrant.

If I want to have a lock for the throttle, and a second for the prop/mix this most expensive option is available:

DJM MFG: 3 Lever Curved Top Side Mount Formation, Three Lever Quadrants, SMCT3L-Formation

www.djmmfg.com

If I want a vernier setup for prop/mixture and a quadrant for throttle, this set of posts has good info:

RV-8 throttle quadrant friction imbalance

Hard to come up for a title for this. However, my prop control is very easy to move and requires the singular quadrant friction lock to be very tight to prevent it advancing to fine pitch. The throttle and mixture are similar to each other but require far less friction lock to stay put. When I...

vansairforce.net

So my questions are these:
1. With the verniers, is the hand position way forward and a pain to deal with, or not a big deal?
2. With the dual-lock quadrant, is any modification to the left panel needed, or is a drop-in?
3. With the single throttle quadrant, which is best and fits in without modification?

I like the pictures that have switches on that left side panel too, which I hadn't thought about before seeing them.

1. There are some out there that have done what you are describing. The vernier do allow much finer adjustment. I don't think the ergonomics are any worse than the standard RV-8 quadrant location.
2. Drop-in
3. I should think four spacers for the mounting bolts and a mod to the cover would be about all that's needed.

 

[walter]

Being able to run LOP is pretty nice and fine control of mixture is handy. You can see the mixture and throttle/prop quadrant on the left. It's exactly where my hand wants it to be.

 

[JDA_BTR]

Being able to run LOP is pretty nice and fine control of mixture is handy. You can see the mixture and throttle/prop quadrant on the left. It's exactly where my hand wants it to be.

That’s a great pic and I like the way you fabbed the bracket onto the cover. The other example has it much more forward. Do you find that the prop control moves much when left unlocked with throttle adjustments?

 

[walter]

It does not move at all.

 

[PCHunt]

One consideration: If you ever intend to fly in formation, a Vernier Throttle is not permitted.

The good reason for that is, that during formation flight, it is not unusual to need relatively large, and quick throttle movements.

Just something else to consider...............

 

[MIKE JG]

One consideration: If you ever intend to fly in formation, a Vernier Throttle is not permitted.

The good reason for that is, that during formation flight, it is not unusual to need relatively large, and quick throttle movements.

Just something else to consider...............

Interesting! Did not know that! Learned something new today!

I plan to do the standard throttle quadrant with Vernier for mix/prop for the very reason you mention, I don't want anything else in the way of the throttle movement. Plus the Vernier style controls in my experience are easier to work with and set up.

 

[ATC_RV8OR]

Being able to run LOP is pretty nice and fine control of mixture is handy. You can see the mixture and throttle/prop quadrant on the left. It's exactly where my hand wants it to be.

View attachment 68585

All the 2 levers I find are throttle and mixture. Yours appears to be marked High and Low for RPM. Where did you get the cover plate like that?