RV News That Caught My Eye Over The Last Day or So ….dr
__________________________
Update on TFR Bust …morganjp
For the hundreds I spoke with at Oshkosh I am now cleared by the secret Service with a much larger file, I am also cleared by the Milwaukee FSDO who was so intrigued with my story that I will be doing some safety speaking enga.gements titled TFRs for dummies. It probably will get recorded and placed as a UTUBE video. For the thousands I did not speak with I hope that you watch the video.
Cherrymax Removal …rsultzbach method
I drilled out quite a few Cherrymax rivets and I used a small piece of aluminum sheet maybe just slightly larger than a rivet checking tool. I drilled a hole in the sheet that just fit over the rivet head perimeter. I taped this shield to the web of the wing spar. With this shield in place I used a conical grinding stone with my Dremel tool with the point used to grind out the locking collar of the rivet. Then, I used a small previously broken punch ground to a blunt point to drive the center mandrel out of the Cherrymax. When the mandrel moved it was easy to drive it out with a regular 3/32 punch. Then just drill out the rivet using the hole where the mandrel was which guides your drill bit like a pilot hole.
This shield technique protected the web whenever a punch or drill slipped giving me a chance to react and stop before nicking a part unintentionally. YMMV
Panel Prep …Biggiesauls
Six months after Phase 1 I decided to add IFR capabilities and start training To my existing dual Dynon HDX panel. Added Garmin GPS-175 and G5 all tied into the Dynon and autopilot. Works sweet.
Slider Handle …Scott Hertha’s
Mine is very similar to Dave’s above. Mounted to the center tube on the canopy frame with two 10-32 flush screws and nuts. Easily lifts the canopy to open.
WDYDWYRTW? (8/3-4/2024)
Bend Radius and Fusion's Sheet Metal module
OFF TOPIC:
PS: Older issues of the ‘VAF News’ can be found at:
__________________________
Fuel Line Overhaul
Background: I found a fuel leak. I posted a thread, which can be found here for context. Got lots of great feedback and began the process of dissassembly and inspection. Update: The T-708 (tank access plate) has been removed. The existing fuel line between the tank and fuselage as well as the...
vansairforce.net
How close is good enough on Aileron & Flap Trailing Edges?
Hi - I made a big mistake and riveted the hinges on my flaps in place before aligning my flaps with my ailerons. It turns out, though, they're pretty close - the flap would need to come out about 1/16" to make it perfect with the aileron in a neutral position. I think this is purely cosmetic...
vansairforce.net
Update on TFR Bust …morganjp
For the hundreds I spoke with at Oshkosh I am now cleared by the secret Service with a much larger file, I am also cleared by the Milwaukee FSDO who was so intrigued with my story that I will be doing some safety speaking enga.gements titled TFRs for dummies. It probably will get recorded and placed as a UTUBE video. For the thousands I did not speak with I hope that you watch the video.
RV6 Busted RNC TFR
https://www.wisn.com/article/norad-f-35-intercepts-aircraft-inside-of-rnc-restricted-airspace/61628964 Check the NOTAMS Boomer Out
vansairforce.net
Cherrymax Removal …rsultzbach method
I drilled out quite a few Cherrymax rivets and I used a small piece of aluminum sheet maybe just slightly larger than a rivet checking tool. I drilled a hole in the sheet that just fit over the rivet head perimeter. I taped this shield to the web of the wing spar. With this shield in place I used a conical grinding stone with my Dremel tool with the point used to grind out the locking collar of the rivet. Then, I used a small previously broken punch ground to a blunt point to drive the center mandrel out of the Cherrymax. When the mandrel moved it was easy to drive it out with a regular 3/32 punch. Then just drill out the rivet using the hole where the mandrel was which guides your drill bit like a pilot hole.
This shield technique protected the web whenever a punch or drill slipped giving me a chance to react and stop before nicking a part unintentionally. YMMV
Removing Cherry Max rivets:
To those that have QB fuselages and wings you will be installing a lot of Cherry Max rivets for the LCP remediation. They are a legal direct replacement for driven rivets. However, they do require special attention and technique. As such, if you are at all like me, you will make a mistake and...
vansairforce.net
Panel Prep …Biggiesauls
Six months after Phase 1 I decided to add IFR capabilities and start training To my existing dual Dynon HDX panel. Added Garmin GPS-175 and G5 all tied into the Dynon and autopilot. Works sweet.
VFR to IFR pannel
I have the standard single G3X VFR pannel. What would be the minimum equipment needed for IFR training?
vansairforce.net
Slider Handle …Scott Hertha’s
Mine is very similar to Dave’s above. Mounted to the center tube on the canopy frame with two 10-32 flush screws and nuts. Easily lifts the canopy to open.
Rear handle on slider canopy
I’m finishing my slider skirts and such and think I need an aft handhold to assist opening. I’ve seen rear handles on sliders mounted on the top bar to help lift the rear from the outside. I do not want to drill my canopy. What options have you all used to help lift the back of the slider? I’m...
vansairforce.net
Jacking a RV-14 on Cleaveland Tools Stainless Tie Down Ring
Hi everyone! I need to jack up my RV-14A for the first time and I have installed these nice STAINLESS TIE DOWN RING (SKU: RVTR4), sold by Cleaveland Tools. Does anyone have any experience if those will hold the weight? Looks like their round shape was designed to actually nest on the cups of...
vansairforce.net
WDYDWYRTW? (8/3-4/2024)
Bend Radius and Fusion's Sheet Metal module
Bend Radius and Fusion's Sheet Metal module
I've been looking for a more powerful CAD tool for my 3D printing. I'm a Mac user, though I do keep a relatively capable Windows 11 laptop to work on my car since that software is Windows only. I had Solid Edge, Shapr3D, and Fusion on my short-list. I'm really drawn to Shapr3D since it is so...
www.vansairforce.net
OFF TOPIC:
PS: Older issues of the ‘VAF News’ can be found at:
Doug's Area ....The VAF News & my flying resume.
Pushed out every now and then.
www.vansairforce.net