About a month ago I launched on a flight from the Denver area to northwestern New Mexico through the Colorado mountains in my RV-7A. I left the airport trimmed for takeoff power and climbed rapidly to about 10k msl before trimming for cruise climb. While leaning I noticed that my oil pressure had dropped to about 35psi. I immediately cranked a 180 degree turn, pulled power and called the tower to declare an emergency. On the way back to the airport I monitored oil pressure and had occasional excursions below 25psi but none for any extended period of time. I made the airport with ease and did not require the assistance from the fire trucks that had been rolled out for me.
Unlike the RV-8 with the blown crank seal, my plane lost its oil out the sides of the cowl through the piano hinges and out the bottom of the cowling. There was very little on the windscreen and except for low oil pressure there was no indication that anything was amiss. I did not know how bad it was till I landed and got out of the plane. The accompanying pictures show the oil streaking down the sides of the plane. The bottom was much worse.
When I removed the cowl, it was evident that the loss of oil was from a blown crank seal. One side was completely blown out and oil was everywhere. My engine had about a quart of oil left in the sump when I drained it. I decided to remove the engine and have my engine shop tear it down. Luckily I did, the main bearings were trashed but the rest of the engine was in good shape. It is now being overhauled.
Once the engine was out I began searching for the cause of the seal failure. In September, 2013 I installed the AntiSplat oil separator with the saddle mount and vacuum valve to help keep my belly clean. That was 165 hours ago. After talking to AntiSplat I removed the saddle mount and vacuum valve and found two items. First, the rivet that holds the vacuum valve together had failed and was lying in engine side of the valve (see pic). This allowed the backing plate on the other side to float free. Blowing through the failed valve showed restriction through the valve toward the exhaust. There was no restriction of flow back toward the engine. Second, the pipe from the valve through the saddle mount was almost completely coked up. There was about an eight inch hole in the coke greatly restricting flow (see pic). I took a pen and attempted to push it through the coked up oil. It did break but it required substantial force to break through the coke. I shot two videos of the mount and valve (http://youtu.be/le1IfyriQ3g and http://youtu.be/LwDsJWxmub0)
I believe the crank seal failure was caused by over-pressuring of the crankcase caused by the AntiSplat products. It is hard to lay the blame for the over-pressuring to either the vacuum valve or the saddle mount. The valve was defective and the saddle mount was almost completely closed off. Either or both in conjunction could have caused the problem. If you have one of these systems on your plane ? Beware. Antisplat has a service bulletin concerning these problems and attempted to notify owners. Unfortunately, I did not receive this notification. If you have not seen it, go to their web site. Also, make sure you have their Safety Bypass Kit installed. As for me, I will run the air/oil separator, but will never again install the saddle mount or vacuum valve on my plane. I was very lucky to have made it back to the airport and will not take that chance again.
Unlike the RV-8 with the blown crank seal, my plane lost its oil out the sides of the cowl through the piano hinges and out the bottom of the cowling. There was very little on the windscreen and except for low oil pressure there was no indication that anything was amiss. I did not know how bad it was till I landed and got out of the plane. The accompanying pictures show the oil streaking down the sides of the plane. The bottom was much worse.
When I removed the cowl, it was evident that the loss of oil was from a blown crank seal. One side was completely blown out and oil was everywhere. My engine had about a quart of oil left in the sump when I drained it. I decided to remove the engine and have my engine shop tear it down. Luckily I did, the main bearings were trashed but the rest of the engine was in good shape. It is now being overhauled.
Once the engine was out I began searching for the cause of the seal failure. In September, 2013 I installed the AntiSplat oil separator with the saddle mount and vacuum valve to help keep my belly clean. That was 165 hours ago. After talking to AntiSplat I removed the saddle mount and vacuum valve and found two items. First, the rivet that holds the vacuum valve together had failed and was lying in engine side of the valve (see pic). This allowed the backing plate on the other side to float free. Blowing through the failed valve showed restriction through the valve toward the exhaust. There was no restriction of flow back toward the engine. Second, the pipe from the valve through the saddle mount was almost completely coked up. There was about an eight inch hole in the coke greatly restricting flow (see pic). I took a pen and attempted to push it through the coked up oil. It did break but it required substantial force to break through the coke. I shot two videos of the mount and valve (http://youtu.be/le1IfyriQ3g and http://youtu.be/LwDsJWxmub0)
I believe the crank seal failure was caused by over-pressuring of the crankcase caused by the AntiSplat products. It is hard to lay the blame for the over-pressuring to either the vacuum valve or the saddle mount. The valve was defective and the saddle mount was almost completely closed off. Either or both in conjunction could have caused the problem. If you have one of these systems on your plane ? Beware. Antisplat has a service bulletin concerning these problems and attempted to notify owners. Unfortunately, I did not receive this notification. If you have not seen it, go to their web site. Also, make sure you have their Safety Bypass Kit installed. As for me, I will run the air/oil separator, but will never again install the saddle mount or vacuum valve on my plane. I was very lucky to have made it back to the airport and will not take that chance again.