VansAirForceForums  
Home > VansAirForceForums

-POSTING RULES
-Advertise in here!
- Today's Posts | Insert Pics

Keep VAF Going
Donate methods

Point your
camera app here
to donate fast.

  #1  
Old 05-03-2009, 10:29 AM
vmirv8bldr's Avatar
vmirv8bldr vmirv8bldr is offline
 
Join Date: Jun 2005
Location: Eastvale, CA
Posts: 378
Default Trutrak flat pack cutout

I had my panel cut, but the about half the holes need to be enlarged a fair amount. I went with a TruTrak AP, and selected the Flat Pack control head. However, to delay expense as much as possible, I don't physically have the head yet. So, does anyone have the dimensions for the cutout in the panel for a DGII Flat Pack? I looked all over TruTrak's website and didn't see it, and I searched here for quite a while to no avail.

If anyone has this head laying around and could measure for me, I would be grateful.

Thanks,
Bart
__________________
Bart Filipiak
Eastvale, CA
RV-8 N74VB

Barrett IO-390
WW200RV
FLYING!!!!!!!
Reply With Quote
  #2  
Old 05-03-2009, 11:02 AM
frazitl's Avatar
frazitl frazitl is offline
 
Join Date: Jan 2005
Location: Las Vegas, NV
Posts: 488
Default

I have mine at the hangar. Could measure for you, but be aware that the corners are cut off of the face plate. That is, the cutout is a rectangle with each corner cut about 1/2" or so. I think it would be very hard to do a decent cutout without the flatpack in hand.

__________________
Terry F.
RV 7A N457RV
250 hours and lovin it!
Southern Nevada EAA Chapter 1300 - www.eaa1300.org

Paid VAF 03/17
Reply With Quote
  #3  
Old 05-03-2009, 11:04 AM
Radomir's Avatar
Radomir Radomir is offline
 
Join Date: Jan 2005
Location: Charlotte, NC
Posts: 1,523
Default

Send me your email address and I'll email it to you.. it's a PDF doc..
__________________
Radomir
RV-7A sold
Reply With Quote
  #4  
Old 05-03-2009, 01:04 PM
Mike S's Avatar
Mike S Mike S is offline
Senior Curmudgeon
 
Join Date: Sep 2005
Location: Dayton Airpark, NV A34
Posts: 15,490
Default contact the mfg.

TruTrack emailed it to me.
__________________
Mike Starkey
VAF 909

Rv-10, N210LM.

Flying as of 12/4/2010

Phase 1 done, 2/4/2011

Sold after 240+ wonderful hours of flight.

"Flying the airplane is more important than radioing your plight to a person on the ground incapable of understanding or doing anything about it."
Reply With Quote
  #5  
Old 05-03-2009, 09:56 PM
SteinAir SteinAir is offline
 
Join Date: Feb 2005
Location: Minneapolis
Posts: 2,473
Default

Hi Bart,

Drop me a line tomorrow of list and I'll send you a 100% drawing or a CAD file of it. Who cut your panel? You shouldn't need to mod the holes if the originating CAD file was good....(now if we cut it, call me a chew me out, because that shouldn't happen)! Our CNC usually will cut holes within a couple thou of what we tell it to.

Cheers,
Stein
Reply With Quote
  #6  
Old 05-04-2009, 05:10 AM
Richard Connell Richard Connell is offline
 
Join Date: Aug 2006
Location: Sydney Australia
Posts: 227
Default For Future ref: Trutrak Digiflight Flat Pack Cutout Dimensions


Last edited by Richard Connell : 05-04-2009 at 05:12 AM.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 03:11 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.