VansAirForceForums  
Home > VansAirForceForums

-POSTING RULES
-Advertise in here!
- Today's Posts | Insert Pics

Keep VAF Going
Donate methods

Point your
camera app here
to donate fast.

  #1  
Old 01-21-2021, 02:52 PM
iamtheari iamtheari is offline
 
Join Date: Nov 2017
Location: ND
Posts: 498
Default Removing Intake Tube on IO-390

I'm probably not the first person to run into this snag. I have the IO-390 engine (the old 210 hp recommended model) on my RV-14. I want to install the sump return fitting for my air-oil separator. I didn't notice until today that the #1 intake tube is going to interfere with installing the 90-degree return fitting for the separator, at least in the forward right sump plug where I believe it needs to go.

Of course, I installed the exhaust system just a week ago and then noticed the problem now.

Does anyone know if the #1 intake tube can be removed with the exhaust headers in place, or do I need to pull the exhaust system first?
Reply With Quote
  #2  
Old 01-21-2021, 03:01 PM
DanH's Avatar
DanH DanH is offline
 
Join Date: Oct 2005
Location: 08A
Posts: 9,812
Default

Return it to #13.

__________________
Dan Horton
RV-8 SS
Barrett IO-390
Reply With Quote
  #3  
Old 01-21-2021, 03:30 PM
iamtheari iamtheari is offline
 
Join Date: Nov 2017
Location: ND
Posts: 498
Default

Thank you! I'll have to get a new fitting since I have the kind with the extended tube, but I think your suggested location makes even more sense for getting the oil back into the sump.
Reply With Quote
  #4  
Old 01-21-2021, 04:42 PM
KHeidorn KHeidorn is offline
 
Join Date: Nov 2013
Location: Heber City, UT
Posts: 119
Default

You will not be able to remove the intake tube without first removing the exhaust.
__________________
Ken Heidorn,
Debur..Dimple..Rivet..Repeat...

"You're never too old to learn something stupid." - unknown
Reply With Quote
  #5  
Old 02-01-2021, 09:46 PM
iamtheari iamtheari is offline
 
Join Date: Nov 2017
Location: ND
Posts: 498
Default

After staring at the engine from many angles on several occasions, I decided to stick with the original location for the oil return fitting. The reason is that the fitting on the accessory housing pictured above in this thread is in a tight spot and appears to be a different size, so there would be cascading changes to my plan for the oil separator installation.

I removed the exhaust headers from cylinders 3 and 4 to allow that part of the exhaust system to drop down a few inches, then removed the intake pipe from cylinder 1 and installed the return fitting. It went smoothly for now, as long as nothing decides to leak on me later.

The only real hassle is that I need to get some more MS35333-41 washers since there seem to only be 8 in the RV-14 kit and I know you're not supposed to re-use those.

Onward and upward!
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 11:16 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.