RV News That Caught My Eye ….dr
__________________________
What did you do w/your RV this weekend? (June 1-2, 2024)
Engine won't start (anymore)!
CSK Instrument Panel Flange Doubler …-14 TASEsq
To close off on this thread, i ended up dimpling the F-1467A angle pieces with sub-structure dies, and dimpled the F-1467B flange doubler with normal dies. Had to upsize the rivets to -3.5. All nested nicely and was a lot quicker and easier than countersinking in my personal opinion.
Prior to painting in the cockpit color, I had to cleco it into the fuse for the money shot.
https://vansairforce.net/threads/csk-instrument-panel-flange-doubler.227106
FF-01226A Missing Hole …12
Fuel tank vacuum for repairing outside seam…Jesse23 update
Gonna try from the outside 1st. It’s weeping and not dripping, but small band aid before pulling the tank. I also removed the nut plate under the fuel line to make the sealant work easier. Will report after a week of dry time.
Interesting find today
OFF TOPIC:
PS: Older issues of the ‘VAF News’ can be found at:
__________________________
What did you do w/your RV this weekend? (June 1-2, 2024)
What did you do w/your RV this weekend? (June 1-2, 2024)
...getting this weekend's thread started! v/r,dr
vansairforce.net
Engine won't start (anymore)!
Engine won't start (anymore)!
UPDATE: was able to do a A/B check with a mag from a friend who just pulled it to install a SureFly .. worked perfectly! I'm going to send in out for IRAN and we'll see what was wrong. I've run into a engine starting issue that I would like your advice on: I no longer can start the engine...
vansairforce.net
CSK Instrument Panel Flange Doubler …-14 TASEsq
To close off on this thread, i ended up dimpling the F-1467A angle pieces with sub-structure dies, and dimpled the F-1467B flange doubler with normal dies. Had to upsize the rivets to -3.5. All nested nicely and was a lot quicker and easier than countersinking in my personal opinion.
Prior to painting in the cockpit color, I had to cleco it into the fuse for the money shot.
https://vansairforce.net/threads/csk-instrument-panel-flange-doubler.227106
FF-01226A Missing Hole …12
FF-01226A Missing Hole
Hi VAF, I am building new carburetor drip trays for my RV-12 because the old ones are corroded and cracking. I got the new parts in from Vans, FF-01226A, FF-01226B, FF-01226C, and FF-01226D. The relevant KAI section is 46-06. The picture in the KAI depicts three holes in one of the areas of the...
vansairforce.net
Fuel tank vacuum for repairing outside seam…Jesse23 update
Gonna try from the outside 1st. It’s weeping and not dripping, but small band aid before pulling the tank. I also removed the nut plate under the fuel line to make the sealant work easier. Will report after a week of dry time.
Fuel tank vacuum for repairing outside seam
Trying to use vacuum to suck in small amount of pro seal (Flamemaster) on bottom inboard flange near drain valve. It doesn’t drip, but starts staining the seam, and I wipe off after each flight. I also noticed the bead of sealant is very gummy on the outside of the seam in that area, when the...
vansairforce.net
Interesting find today
Interesting find today
I'm doing my condition inspection and the intake valve on #4 cylinder apparently has an issue. Compression on that cylinder went from 78# to 74# in the last 18 hours and when borescoped it has a definite hot spot. I really don't want to pull the cylinder unless necessary so what should be my...
www.vansairforce.net
OFF TOPIC:
PS: Older issues of the ‘VAF News’ can be found at:
Doug's Area ....The VAF News & my flying resume.
Pushed out every now and then.
www.vansairforce.net