VansAirForceForums  
Home > VansAirForceForums

-POSTING RULES
-Advertise in here!
- Today's Posts | Insert Pics

Keep VAF Going
Donate methods

Point your
camera app here
to donate fast.


Go Back   VAF Forums > Model Specific > RV-12/RV-12iS
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 10-31-2021, 05:00 PM
amekler amekler is offline
 
Join Date: Aug 2009
Location: Gilford,NH
Posts: 136
Default Right CHT not working 912ULS

I did my first engine start today. All went except no right CHT.
I swapped the right and left sensors and still no right cht. What should I do next to troubleshoot?
A. Mekler
Reply With Quote
  #2  
Old 10-31-2021, 08:02 PM
Bob Y Bob Y is online now
 
Join Date: Jul 2017
Location: Piedmont, SC
Posts: 302
Default

Sounds like a connector/electrical issue. Id start wiggling connectors to see if you can find a loose one.
__________________
Bob Y - builder 12iS E-LSA
N569TT first flight 2/9/2020
#121047
Reply With Quote
  #3  
Old 11-01-2021, 10:11 PM
RFSchaller RFSchaller is offline
 
Join Date: Oct 2010
Location: Phoenix, AZ
Posts: 3,165
Default

Try putting an ohm meter on the pin at the connector to your MFD and the connector forward of the firewall to check continuity.
Reply With Quote
  #4  
Old 11-02-2021, 02:38 AM
PaulvS's Avatar
PaulvS PaulvS is offline
 
Join Date: Aug 2019
Location: Western Australia
Posts: 784
Default No CHT or CHT zero?

Just to clarify: "no CHT", does that mean there is no CHT at all displayed, or is it that there is a CHT but it does not go up when the engine warms up? If it is the former, then check the EMS configuration for two CHTs enabled. Otherwise check for electrical continuity from the sensor connector back to the EMS, as others have said.
__________________
Paul vS (yes I'm also a Van)
Building RV-6A #22320 O-320 FP. Wings and tail complete, working on fuselage
Flying my Aeroprakt A-22 STOL and the aero club's RV-9A while I build
Reply With Quote
  #5  
Old 11-02-2021, 05:20 AM
amekler amekler is offline
 
Join Date: Aug 2009
Location: Gilford,NH
Posts: 136
Default

The right cht display has an X through it.
I checked the voltage at the wire going to the sensors both were 5.0 volts. The left CHT connected and reading normally shows 3.0 volts but the right CHT
only .365 volts. As I said before I swapped sensors so it isn't the sensor.
My thoughts are the problem must be in the wiring to the EMS-200.
This harness came prewired .
Hopefully today I will pull apart the panel and see what's going on .
Alan
Reply With Quote
  #6  
Old 11-02-2021, 08:09 AM
Piper J3's Avatar
Piper J3 Piper J3 is offline
 
Join Date: Nov 2014
Location: Hinckley, Ohio
Posts: 2,566
Default

Its possible that a pin got pushed back in the D-sub connector. If pin isn't seated well in the plastic housing it can slip when force is applied.
__________________
-
Jim Stricker - EAA #499867
PPL/ASEL 1970 - Sport Pilot since 2007
80 hrs Flying Aeronca Chief 11AC N86203
1130 hrs Flying 46 Piper J-3 Cub N6841H
Bought Flying RV-12 #120058 Oct 2015 with 48TT - Hobbs now 750

LSRM-A Certificate 2016 for RV-12 N633CM
Special Thanks... EJ Trucks - USN Crew Chief A-4 Skyhawk
MJ Stricker (Father - CFI) - USAAF 1st Lt. Captain B-17H
Reply With Quote
  #7  
Old 11-02-2021, 04:32 PM
amekler amekler is offline
 
Join Date: Aug 2009
Location: Gilford,NH
Posts: 136
Default

pins in the correct places andcseated
wires intact
both read the same ohms
sensors both work
talked to Dynon-maybe a problem within the EMS-220

Alan
Reply With Quote
  #8  
Old 11-02-2021, 08:05 PM
ChuckC ChuckC is offline
 
Join Date: Apr 2011
Location: Meridian, ID
Posts: 80
Default

After installing software version 16, my Engine Management System (EMS) disappeared. I tried a fix suggested by someone on this forum, and, the EMS came back; except for the right cylinder head temperature (which has a big red X thru it).

Called Dynon and the tech rep put me thru some paces and we found there was no information getting to the CHT-R. Tech suggested switching the left CHT wire to the right CHT to test the right sensor. If that didn't work, then he thought there was a wiring problem.

I did what the tech first suggested and found the right CHT sensor is working fine. I have been looking at the wiring in the engine compartment and can find nothing wrong with the wiring. Then sprayed some electrical contact cleaner on the right sensor and the clip on the end of the wire and wiped everything clean. Have not been back to the hangar to see if the cleaner got the CHT-R operational. If not, I'll look in the avionics bay to see if I can find a wiring problem.

As background, my RV-12ULS originally was partially built with wiring for the D180. Then the nice Skyview came out and I decided to upgrade in mid-build. Van's Aircraft provided a conversion harness. I remember something did not work and Van's tech guys had me move one pin in one of the connectors - everything worked beautifully until this software version 16 came out. Now I am pondering if there is a wire that is bad, or, is there a small group of us with the conversion harness that are having the same problem? And, maybe it is related to the software 16?

Let's stay in contact.
__________________
Chuck Carlson
120445
Reply With Quote
  #9  
Old 11-03-2021, 04:42 AM
amekler amekler is offline
 
Join Date: Aug 2009
Location: Gilford,NH
Posts: 136
Default

chuck,
,
I called Dynon yesterday as I see no wiring issues. they want me to send a photo of the sensor debug page. I think the problem lies in the EMS-220. This was my first engine start. Now after seeing your post I wonder if it is a configuration issue
Stay in touch.

Alan
Reply With Quote
  #10  
Old 11-04-2021, 06:54 PM
amekler amekler is offline
 
Join Date: Aug 2009
Location: Gilford,NH
Posts: 136
Default

today I went to the sensor debug page and noticed that right cht was in pin 11 not pin 22 as it supposed to be
called vans and they recommended redownloading the set up files and reinstalling
will try that tomorrow
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 09:40 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.