VansAirForceForums  
Home > VansAirForceForums

-POSTING RULES
-Advertise in here!
- Today's Posts | Insert Pics

Keep VAF Going
Donate methods

Point your
camera app here
to donate fast.


Go Back   VAF Forums > Model Specific > RV-3
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 09-03-2021, 11:26 PM
RV3Kev RV3Kev is offline
 
Join Date: Sep 2017
Location: Traralgon Australia
Posts: 46
Default RV3 Rudder Fiberglass Mounting Strips

On the rudder, in order to mount the base fiberglass a strip of needs to be added to the bottom flange. Its not shown in the plans but it's often mentioned on build sites.

a) What thickness. I have made two sets one in 0.025 and 0.032.
b) I made the width to project 1" beyond the flange.
c) What's the best methods for attaching the fiberglass to the aluminum sheet. Screws and nut plates or pop rivets, other ways ?


Any comments would be appreciated


Kevin
Reply With Quote
  #2  
Old 09-04-2021, 09:26 AM
RWoodard's Avatar
RWoodard RWoodard is offline
 
Join Date: Jan 2005
Location: Brighton, Colorado
Posts: 471
Default

I've now seen fiberglass tips attached via 2 different methods. I think the more common method is to attach an aluminum flange to the aluminum part and then make the fiberglass part meet flush against the aluminum part (in your case, the rudder). If using this method, you may want to add a shim under the flange so that the fiberglass part can be a bit thicker than the rudder skin and still sit flush.

The other option is to just tuck the fiberglass part under the edge of the rudder skin and accept that the part won't fit exactly flush because the thickness of the aluminum skin will sit on top the fiberglass tip. I recently messed with my vertical stabilizer fiberglass tip and realized that the original builder used this technique. I have to admit that the thickness of the skin protruding on top the fiberglass piece wasn't (isn't) objectionable at all and is actually hardly noticeable. Using this technique, the fiberglass piece just needs to extend far enough into the vertical stabilizer to allow for fasteners.

No matter which technique you choose... an innie or an outie, I'd suggest installing nutplates for ease of access/maintenance in the future. My rudder bottom has a tail light in it and the top of the vertical stab has a strobe. I just recently replaced the strobe and I'm happy that I didn't have to mess up the paint on the VS to replace the strobe.

Here's an example where the fiberglass piece sits inside the Vertical Stabilizer. There are nutplates installed inside the fiberglass piece and the VS skin is dimpled to accept normal flathead (flush) screws.
Attached Thumbnails
Click image for larger version

Name:	Strobe2.jpg
Views:	52
Size:	189.0 KB
ID:	15395  
__________________
Rod Woodard
Brighton, Colorado (CO12)
RV-3 IO-320
Reply With Quote
  #3  
Old 09-04-2021, 05:39 PM
sf3543 sf3543 is offline
 
Join Date: Jan 2005
Location: San Antonio, TX
Posts: 1,091
Default Here’s how I did mine

I used a metal flange and a spacer to allow for the fiberglass thickness and blind riveted the fairing on.
Attached Thumbnails
Click image for larger version

Name:	4DE95772-A0B1-4124-BC90-DF4FDA249FD3.jpeg
Views:	55
Size:	855.2 KB
ID:	15409  
__________________
Steve Formhals
A&P, Tech Counselor & Flight Advisor
RV3B
Legend Cub
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 03:39 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.