VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 03-20-2015, 07:38 AM
PeteP's Avatar
PeteP PeteP is offline
 
Join Date: Jun 2011
Location: Chesapeake, VA
Posts: 219
Default Skybolt fastener adjustment

Starting to adjust my skybolts to the final depth setting. Looks like if you tighten them too snug it will be very difficult to have enought depth to get then to release when removing. Any good tips or ideas on the proper snugness before removing the locking pins?
__________________
Pete (AKA Yoda)
Exempt but VAF 2017 Dues Paid anyway
Reply With Quote
  #2  
Old 03-20-2015, 07:59 AM
Ron RV8's Avatar
Ron RV8 Ron RV8 is offline
 
Join Date: Nov 2010
Location: Okanagan Valley BC, Canada
Posts: 483
Default

They tell you how much 1 turn will adjust the fastener. They're something like 40 threads per inch. Put the cowl on and note beside each fastener approx how many turns up or down they need to go... Remove cowl and adjust. Re install cowl and see if ya got it right. Repeat till you're tired or happy...
__________________
Ron Townson
Okanagan Valley BC, Canada
RV-8 Completed Dec 2013

Membership renewed Sept 8, 2019
Reply With Quote
  #3  
Old 03-20-2015, 08:36 AM
flion's Avatar
flion flion is offline
 
Join Date: Dec 2007
Location: Flagstaff, AZ
Posts: 2,653
Default

I did Mil-Spec but it should be pretty similar. Put the cowl on, tighten the fasteners as if they were screws, and spend some time making sure all the fastener heads are nearly flush with the grommets (better slightly deep to slightly proud). You will find that tightening/loosening one will change the neighbors, so take your time. Beat on the cowl a bit to be sure it is settled into place. When you are happy with the fasteners, remove them by pushing in fully to disengage (being lazy here will undo your adjustments). Start at the corners, which tend to be tightest, and work toward the edges. Now you can pull the pins, reinstall the cowl, and check again; most of your fasteners should be right on. I checked again after a few flights to find a few high fasteners that I re-adjusted. I also found a couple of low ones, spotted because they broke one of the cam pins during operation - a good reason to have a few spares handy. Re-adjustment is not hard and usually takes less than a turn.
__________________
Patrick Kelley - Flagstaff, AZ
RV-6A N156PK - Flying too much to paint
RV-10 14MX(reserved) - Fuselage on gear
http://www.mykitlog.com/flion/
EAA Technical Counselor #5357
Reply With Quote
  #4  
Old 03-20-2015, 08:43 AM
DonFromTX's Avatar
DonFromTX DonFromTX is offline
 
Join Date: Oct 2010
Location: La Feria Texas
Posts: 3,822
Default

Mine are giving me fits as well. If I go too tight, the cowl forms a depression by the skybolt. If I am too loose, the screw is not sucked down into its fitting. I am considering adding some fiberglass to the underside of the cowling by the bolts to stiffen it up a bit. Comments?
__________________
A&P, PP-SEL, Pathological Flier, EAA Technical Counselor
EAA Chapter 595 President,http://www.595.eaachapter.org/index.htm
Retired US Army Officer
Reply With Quote
  #5  
Old 04-02-2015, 10:51 AM
NBowers NBowers is offline
 
Join Date: Dec 2006
Location: Leesburg, FL
Posts: 89
Default Adjusting Skybolt Fastenrs

The Skybolt Diamondhead Fasteners used in Vans RV kits utilize an adjustable receptacle that we designed and patented in the early 1990s. The adjustment thread is 1/2-32 or 32 threads per inch which works out to be .030 adjustment per 360 degree turn. There are two locking grooves that allow adjustment increments of .015.

Before making the initial adjustment setting, check that the receptacle inserts are near the face of the receptacle. If they are too deep, you will not be able to engage the studs. Place the cowling in position and engage all fasteners. Screw the fasteners in as if they were machine screws until the heads are flush with the grommets. Use a quick push turn motion to unlock the fasteners without disturbing the receptacle inserts. With the cowling removed, pull all anti-lock pins. With a flat blade screwdriver, turn each insert clockwise until the receptacle locking band engages into the insert locking groove.

Note: It is possible to screw the studs all the way into the base of the grommet (head about .030 below the surface). If you had access to the anti-lock pin and removed it, it may be impossible to unlock the fastener. Without breaking the fastener, you must unlock the receptacle and return the setting such that the fastener head is flush with the grommet face. If you ever installed a Dzus fastener, our receptacle design can be described as an up-side-down Dzus fastener. The Dzus stud geometry is very similar to our receptacle insert thus the same locking dynamics.

It helps to look closely at the locking slot in the receptacle insert and note how it works. As the fastener is turned, it is drawn inward to an apex in the locking slot, then rebounds .020 to .030 into a locking saddle. So the fastener must have approximately .030 compression remaining when locked for the pin to retrace the motion over the apex when unlocking.

Re-install cowling and attempt to lock all fasteners. If the locking action requires more than about 10 inch-lbs (notable force), do not attempt to force the fastener; the adjustment at that location is set too deep. The Skybolt Diamondhead studs are very hard and you can over stress the crosspin with no galling like other brands. We have strengthened the crosspin to perform at levels beyond steel fasteners, but severe torsion will exceed the design load of the pin. Most initial adjustments should be right on the money.

For any locations where the heads are not flush or studs will not lock, use a small piece of masking tape and place it on the lower cowl or the airframe adjacent to the firewall. Write a -1, +1, -1.5.....to indicate how many half turns you estimate to make the heads flush with the grommets. If it appears the head is .015 high, mark the tape with -1 such that with the cowling removed, you know to adjust that location 1/2 turn or .015 in. If the stud will not lock, start with +1 or 1 full turn at that l location.

You can set and lock a complete cowling in the time it takes to read this information.

Skybolt is running a 20% promotion on complete Vans RV Cowling Kits from now through April 26, 2015 (Sun N Fun Special). If you have any questions, please call us at 1-800-223-1963. All Skybolt kits have our latest revisions in hardened Diamondhead studs, high shear grommets, enhanced receptacles, including our patented interlocking mounting flanges.
Reply With Quote
  #6  
Old 08-06-2020, 07:45 AM
KayS KayS is offline
 
Join Date: Jul 2009
Location: lake constance
Posts: 248
Default

I do have problems to adjust the depth of the fasteners. The skybolt fastener kit ordered in 2010 was RV67910J-C1P (with receptacle SK245A162A).

I can't see any locking spring or something on the outside of the receptacle, instead there seems to be a small pin inside the receptacle that prevents it from turning. Does anybody has an idea how to unlock the device?

Last edited by KayS : 08-06-2020 at 07:59 AM.
Reply With Quote
  #7  
Old 08-08-2020, 07:00 AM
FredMagare FredMagare is offline
 
Join Date: Mar 2006
Location: Kyle, TX
Posts: 566
Default

Quote:
Originally Posted by KayS View Post
Does anybody has an idea how to unlock the device?
If you look at the locking barrel, you will notice a small opening on the side (a black locking spring tab will be at that location too). Inserting a dental pick into this hole will raise the locking spring tab which will allow you to turn the Skybolt to the appropriate depth (Mine are flush with the cowl.) When you remove the pick from the hole, rotate the Skybolt forward or aft until the spring locking tab engages and locks the barrel....

I know this is probably difficult to picture. I would recommend a Youtube search which will likely prove more helpful. I was initially rather confused until I installed and re-adjusted the first one. After that it was easy peasy lemon squeezy!
__________________
Fred Magare
GySgt, USMC (Ret.)
PP-ASEL, A&P
Frederic.magare "at" gmail.com
RV-9A Firewall Forward
[Engine purchased]
Reply With Quote
  #8  
Old 08-22-2020, 10:49 AM
KayS KayS is offline
 
Join Date: Jul 2009
Location: lake constance
Posts: 248
Default

Fred: thank you for your reply but my fasteners are different. There's no locking spring on the side of the barrel. There's just a pin in the barrel that i can not move. I wrote three emails to skybolt ( first three weeks ago) but no response yet. I wonder if they are still in business.
Reply With Quote
  #9  
Old 08-24-2020, 05:00 AM
FredMagare FredMagare is offline
 
Join Date: Mar 2006
Location: Kyle, TX
Posts: 566
Default

Can you email me a photo of the back of the receptacle? Maybe I can annotate the picture with the location of the locking tab. Also, if they are similar to mine, I can make and send you a short video of how to unlock them....

(email is preferable. it is listed in my signature.)
__________________
Fred Magare
GySgt, USMC (Ret.)
PP-ASEL, A&P
Frederic.magare "at" gmail.com
RV-9A Firewall Forward
[Engine purchased]
Reply With Quote
  #10  
Old 08-24-2020, 09:37 AM
John Tierney John Tierney is offline
 
Join Date: Jan 2006
Location: Vonore, TN
Posts: 369
Default

This is from the installation manual that I used.
Attached Thumbnails
Click image for larger version

Name:	Skybolt Adjustment.jpg
Views:	62
Size:	58.2 KB
ID:	1589  
__________________
John Tierney
Vonore, TN
RV-7A - N777JT Flying
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 04:14 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.