VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 01-30-2015, 07:44 AM
DragonflyAero DragonflyAero is offline
 
Join Date: Jan 2013
Location: Greensboro, NC
Posts: 173
Default Slider track positioning

I have read through many, many threads but am still confused on setting the proper spacing for the slider tracks. The manual talks about setting the side bows to 1/16" in from the side skins, but then I understand that the side bows move to the outside by 1/2" when the weight of the canopy is added.

If I set the tracks to the specified 40 13/16" between vertical piece as mentioned in the manual the side bows are still well inside the 1/16" from side skins.

Should the tracks just be positioned and drilled relative to the canopy decks and then the canopy frame adjusted as needed after checking measurements with the canopy on the frame?

Thanks!!!
__________________
Bill Vinson
RV-7 Standard Build
http://www.mykitlog.com/users/index....r&project=2226
Reply With Quote
  #2  
Old 01-30-2015, 07:53 AM
krw5927 krw5927 is offline
 
Join Date: Aug 2010
Location: Wichita, KS
Posts: 1,958
Default

Quote:
Originally Posted by DragonflyAero View Post
Should the tracks just be positioned and drilled relative to the canopy decks and then the canopy frame adjusted as needed after checking measurements with the canopy on the frame?
You got it!
__________________
Kurt W.
RV9A
FLYING!!!
Reply With Quote
  #3  
Old 01-30-2015, 08:08 AM
frazitl's Avatar
frazitl frazitl is offline
 
Join Date: Jan 2005
Location: Las Vegas, NV
Posts: 488
Default

The position of the tracks is pretty much set by the fuselage width. Trim the aft ends and clamp in place. The frame will spread when you install the canopy so my process was to clamp the plexi in place with spring clamps to take width measurements. You can't move the frame after the plexi is installed without risking a crack. It won't be perfect but a lot can be done with the side and aft skirts to get a nice fit.
__________________
Terry F.
RV 7A N457RV
250 hours and lovin it!
Southern Nevada EAA Chapter 1300 - www.eaa1300.org

Paid VAF 03/17
Reply With Quote
  #4  
Old 01-30-2015, 09:17 AM
RhodeIsland9 RhodeIsland9 is offline
 
Join Date: Mar 2010
Location: Middletown, RI
Posts: 36
Default

Depending on your fuse width, you might want to cheet the aft ends of the tracks inboard (not parallel) to avoid a large fish mouth. see thread

http://www.vansairforce.com/communit...ad.php?t=99685
__________________
Jared Waite
RV9-A Flying
Superior IO-320
Catto 3 Blade
Reply With Quote
  #5  
Old 01-30-2015, 10:05 AM
vlittle's Avatar
vlittle vlittle is offline
 
Join Date: Jan 2005
Location: Victoria, Canada
Posts: 2,251
Default

The width of the Rv fuselages differs at the roll bar location because this was not accurately jigged during construction. This means that the dimensions that Van's provide are not very useful. I have found up to a one inch variance!

Ideally, you would use a hydraulic press or straps to tweak the fuse to the correct width before you attach the roll bar, but it's easier to bend the canopy frame.

At some point, if you are unlucky, you may need to cut the aft canopy frame hoops to make it fit, but even though you may consider this a traumatic experience, it can be welded or rivet back together.

Pity the poor Rocket builders who's canopy frame comes completely unwelded. This turned out to be the easiest way to get a perfect fit.... And completely without angst.

The slider fit is always a challenge... The RV-14 doesn't even allow for one.
__________________
===========
V e r n. ====
=======
RV-9A complete
Harmon Rocket complete
S-21 wings complete
Victoria, BC (Summer)
Chandler, Az (Winter)
Reply With Quote
  #6  
Old 01-30-2015, 12:46 PM
DragonflyAero DragonflyAero is offline
 
Join Date: Jan 2013
Location: Greensboro, NC
Posts: 173
Default

Thanks everyone!! I will position and drill the side tracks based on the fuselage and your collective suggestions. I want to wait for warmer weather before I start cutting on the canopy but would like to get the tracks drilled before I move on to another area.
__________________
Bill Vinson
RV-7 Standard Build
http://www.mykitlog.com/users/index....r&project=2226
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 02:02 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.