VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 05-16-2014, 06:46 AM
dinowal dinowal is offline
 
Join Date: Dec 2011
Location: TWIN WATERS, Queensland, AUSTRALIA
Posts: 89
Default Canopy fiberglass layup

I am about to attempt the canopy fibreglass fairing layup. I have read the instructions several times but still have a query. Step 1 on page 34-13 says to lower the canopy after doing some masking & adding duct tape. Figure1 on that page shows the canopy down with the canopy strut in the compressed position. All of the work on pages 34-13,14 & 15 is done with the canopy closed, then step 1 on page 34-16, after drilling a hole to access the pivot bolts, the instruction is to remove the pivot bolts & remove the canopy. The struts are still compressed, & it is dangerous & difficult to remove bolts when they are in this state; I know this because I foolishly started to unscrew one of the strut bolts some time ago, with a result that caused me to buy a new strut & nurse a bruised thumb. Have I missed something, or should I remove the struts totally before starting the fibreglass work? Thanks for any help/advice, Cheers, DEAN...
Reply With Quote
  #2  
Old 05-16-2014, 11:59 AM
cactusman cactusman is offline
 
Join Date: Oct 2012
Posts: 421
Default

Quote:
Originally Posted by dinowal View Post
I am about to attempt the canopy fibreglass fairing layup. I have read the instructions several times but still have a query. Step 1 on page 34-13 says to lower the canopy after doing some masking & adding duct tape. Figure1 on that page shows the canopy down with the canopy strut in the compressed position. All of the work on pages 34-13,14 & 15 is done with the canopy closed, then step 1 on page 34-16, after drilling a hole to access the pivot bolts, the instruction is to remove the pivot bolts & remove the canopy. The struts are still compressed, & it is dangerous & difficult to remove bolts when they are in this state; I know this because I foolishly started to unscrew one of the strut bolts some time ago, with a result that caused me to buy a new strut & nurse a bruised thumb. Have I missed something, or should I remove the struts totally before starting the fibreglass work? Thanks for any help/advice, Cheers, DEAN...
I just did mine and left all the hardware installed when I did the layups. There are some very good blogs and threads on here to help. But a good removal system includes mylar tape, good electrical tape, good removal wax, taping everything that you don't want to be part of the new assembly including the gaps, the struts, using foam and mylar tape to cover the gaps, and a very thin spatula/cake icing applicator thingy.

With a little of the above and planning and coaxing the struts will help the canopy tip up and then you can remove it to finish trimming, sanding, etc.

BTW, I found this whole thing very intimidating during the reading/planning stages, but it actually worked out pretty well.
Reply With Quote
  #3  
Old 05-16-2014, 12:11 PM
DonFromTX's Avatar
DonFromTX DonFromTX is offline
 
Join Date: Oct 2010
Location: La Feria Texas
Posts: 3,822
Default

Quote:
Originally Posted by cactuspilot View Post
BTW, I found this whole thing very intimidating during the reading/planning stages, but it actually worked out pretty well.
I found the same. I just tell everyone to "get over it" and get it done!
__________________
A&P, PP-SEL, Pathological Flier, EAA Technical Counselor
EAA Chapter 595 President,http://www.595.eaachapter.org/index.htm
Retired US Army Officer
Reply With Quote
  #4  
Old 05-16-2014, 12:30 PM
RFSchaller RFSchaller is offline
 
Join Date: Oct 2010
Location: Phoenix, AZ
Posts: 2,820
Default

You'll get a nice access hole if you cut a short piece of aluminum tubing with an ID just big enough to slip in a 7/16 socket. Put the socket on the bolt head and slip the tube over it. Then glass over it. When the fiberglass sets you can easily remove to glass from the center with a moto tool and end up with a nice round access hole that won't chip. I also put a mixture of resin and flock around the tube before glassing to ensure it is solid.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 02:13 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.