VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Main > RV General Discussion/News
Register FAQ Members List Calendar Today's Posts

Reply
 
Thread Tools Search this Thread Display Modes
  #11  
Old 04-18-2014, 07:25 AM
DanH's Avatar
DanH DanH is offline
 
Join Date: Oct 2005
Location: 08A
Posts: 9,500
Default

Quote:
Originally Posted by BillL View Post
I am trying to get direct connection with owners with skybolt fasteners, of all combinations, to come to a conclusion about what to do as I believe it is universal that all floaters will not result in a sufficiently rigid cowl.
An all-floating setup may be fine, but it's not necessary. In the photo, three floaters in each upper corner allow the fasteners to self-enter the receptacles when the cowl is set into place. All the others are solid mounts.

BTW, if done over I would not scallop the mounting strip for the lowest two of those three. The last scallop can catch the corner of the cowl and chip paint. Same for the straight sections along the sides of the lower cowl...no scallops.

__________________
Dan Horton
RV-8 SS
Barrett IO-390
Reply With Quote
  #12  
Old 04-18-2014, 07:52 AM
Kahuna's Avatar
Kahuna Kahuna is offline
 
Join Date: Dec 2004
Location: Gold Hill, NC25
Posts: 2,400
Default Why floaters are bad

When you install the floaters on a new install, everything seems fine. And it is for the first 500 hours or so. What you find is that since the floaters float, they wear out the holes in the fiberglass as your engine moves around. The result is that over time the holes wear larger and larger to the point that the paint wears, holes enlarge, screws fall out when removing the cowl, and eventually its a mess. Ask me how I know.
All of my holes in the cowl are completely wore out. All the male screws fall out when you unlatch to remover the cowl, and the cowl moves A LOT now. I can lift on the fwd cowl when attached and move my entire cowl around. The fix for this is AWFUL. Means a new cowl.

One fix they had to keep the screws in was a larger c-clip. I went to those about 1k hours ago. Worked for a few hundred hours but eventually it wore beyond what the larger clips could retain. ARGH!

Note: Im certain that the type of aggressive flying I do, exacerbates the problem. If your pulling positive and negative G's a lot, your stressing these cams on the fiberglass forcing a lot of joint movement. I would NOT do floaters again anywhere on my cowl.
__________________
Kahuna
6A, S8 ,
Gold Hill, NC25
Reply With Quote
  #13  
Old 04-18-2014, 08:24 AM
DonFromTX's Avatar
DonFromTX DonFromTX is offline
 
Join Date: Oct 2010
Location: La Feria Texas
Posts: 3,822
Default

Thanks for that information. Of course if I flew my 12 as you do your airplane, the tail would fall off long before my cowling was worn out
I am thinking on using my floaters as they recommend as of now.

Quote:
Originally Posted by Kahuna View Post
When you install the floaters on a new install, everything seems fine. And it is for the first 500 hours or so. What you find is that since the floaters float, they wear out the holes in the fiberglass as your engine moves around. The result is that over time the holes wear larger and larger to the point that the paint wears, holes enlarge, screws fall out when removing the cowl, and eventually its a mess. Ask me how I know.
All of my holes in the cowl are completely wore out. All the male screws fall out when you unlatch to remover the cowl, and the cowl moves A LOT now. I can lift on the fwd cowl when attached and move my entire cowl around. The fix for this is AWFUL. Means a new cowl.

One fix they had to keep the screws in was a larger c-clip. I went to those about 1k hours ago. Worked for a few hundred hours but eventually it wore beyond what the larger clips could retain. ARGH!

Note: Im certain that the type of aggressive flying I do, exacerbates the problem. If your pulling positive and negative G's a lot, your stressing these cams on the fiberglass forcing a lot of joint movement. I would NOT do floaters again anywhere on my cowl.
__________________
A&P, PP-SEL, Pathological Flier, EAA Technical Counselor
EAA Chapter 595 President,http://www.595.eaachapter.org/index.htm
Retired US Army Officer
Reply With Quote
  #14  
Old 04-18-2014, 08:35 AM
rocketbob's Avatar
rocketbob rocketbob is offline
 
Join Date: Jun 2006
Location: 8I3
Posts: 3,564
Default

Even the fixed receptacles are not very tight and allow some movement. My rocket has hinges for the cowling sides and the fixed Skybolt receptacles around the firewall. There is some movement of the cowling that can occur as Kahuna points out and I have considered adding 2 regular screws and nutplates to stop the movement. Which kind of defeats the purpose of camlocks. If I had to do it over again I would just go with #10 flush screws and tinnerman washers. Cheap, much easier to install, easier to replace. Most of the time I use an electric screwdriver to remove screws so the time savings and convenience of camlocs isn't all that that much better.
__________________

Please don't PM me! Email only!

Bob Japundza CFI A&PIA
N9187P PA-24-260B Comanche, flying
N678X F1 Rocket, under const.
N244BJ RV-6 "victim of SNF tornado" 1200+ hrs, rebuilding
N8155F C150 flying
N7925P PA-24-250 Comanche, restoring
Not a thing I own is stock.

Last edited by rocketbob : 04-18-2014 at 08:42 AM.
Reply With Quote
  #15  
Old 04-18-2014, 09:57 AM
Kyle Boatright Kyle Boatright is offline
 
Join Date: Aug 2005
Location: Atlanta, GA
Posts: 4,218
Default

Quote:
Originally Posted by rocketbob View Post
Even the fixed receptacles are not very tight and allow some movement. My rocket has hinges for the cowling sides and the fixed Skybolt receptacles around the firewall. There is some movement of the cowling that can occur as Kahuna points out and I have considered adding 2 regular screws and nutplates to stop the movement. Which kind of defeats the purpose of camlocks. If I had to do it over again I would just go with #10 flush screws and tinnerman washers. Cheap, much easier to install, easier to replace. Most of the time I use an electric screwdriver to remove screws so the time savings and convenience of camlocs isn't all that that much better.
Funny that there doesn't seem to be a universally preferred setup after all these years. I've grown weary of my installation with ten #6 screws across the top of the firewall plus eight #6's and two #8's across the bottom of the firewall. There are 40 individual pieces of hardware along the firewall (20 screws plus 20 tinnermans), the side hinges, and the screws at the inlets every time I pull the cowl.

I will say that my setup has held up well.

I wonder if anyone makes industrial strength Velcro. ;-)
__________________
Kyle Boatright
Marietta, GA
2001 RV-6 N46KB
2019(?) RV-10
Reply With Quote
  #16  
Old 04-18-2014, 10:58 AM
NDrv8r's Avatar
NDrv8r NDrv8r is offline
 
Join Date: Dec 2009
Location: Bismarck, ND
Posts: 212
Default SkyBolt

I have floaters all the way on the top. Doing it again, I would probably use screws.
I have had 2 issues with the floaters.
1. I have had several of the self adjusting mechanisms fail even after making sure the ball is aligned in its slot.
2. I have had several of the floaters fall out of their retainers.
__________________
Larry Buller
RV7A slow build, Tip up, IO360 200hp, Catto 3 blade, Dynon Skyview, arinc 429, ems, SV transponder, Garmin GNS430w, Aera 560, Dynon D6.
FLYING!
Reply With Quote
  #17  
Old 04-18-2014, 08:15 PM
BillL BillL is offline
 
Join Date: Sep 2007
Location: Central IL
Posts: 5,516
Default

Quote:
Originally Posted by DanH View Post
An all-floating setup may be fine, but it's not necessary. In the photo, three floaters in each upper corner allow the fasteners to self-enter the receptacles when the cowl is set into place. All the others are solid mounts.

BTW, if done over I would not scallop the mounting strip for the lowest two of those three. The last scallop can catch the corner of the cowl and chip paint. Same for the straight sections along the sides of the lower cowl...no scallops.
Thanks Dan, I called Skybolt and they will swap my package for a new one with only 6 floaters, just like you recommend. I will make the cowl split straight with fiberglass, like you and a previous poster recommend.

Quote:
Originally Posted by Kahuna View Post
When you install the floaters on a new install, everything seems fine. And it is for the first 500 hours or so. What you find is that since the floaters float, they wear out the holes in the fiberglass as your engine moves around. The result is that over time the holes wear larger and larger to the point that the paint wears, holes enlarge, screws fall out when removing the cowl, and eventually its a mess. Ask me how I know.
All of my holes in the cowl are completely wore out. All the male screws fall out when you unlatch to remover the cowl, and the cowl moves A LOT now. I can lift on the fwd cowl when attached and move my entire cowl around. The fix for this is AWFUL. Means a new cowl.

One fix they had to keep the screws in was a larger c-clip. I went to those about 1k hours ago. Worked for a few hundred hours but eventually it wore beyond what the larger clips could retain. ARGH!

Note: Im certain that the type of aggressive flying I do, exacerbates the problem. If your pulling positive and negative G's a lot, your stressing these cams on the fiberglass forcing a lot of joint movement. I would NOT do floaters again anywhere on my cowl.
Thanks Kahuna, I remembered someone from a few years ago that said this, it must have been you. I asked the SB people about shear vibration testing and they said none was done. Thanks for your experience.

Quote:
Originally Posted by rocketbob View Post
Even the fixed receptacles are not very tight and allow some movement. My rocket has hinges for the cowling sides and the fixed Skybolt receptacles around the firewall. There is some movement of the cowling that can occur as Kahuna points out and I have considered adding 2 regular screws and nutplates to stop the movement. Which kind of defeats the purpose of camlocks. If I had to do it over again I would just go with #10 flush screws and tinnerman washers. Cheap, much easier to install, easier to replace. Most of the time I use an electric screwdriver to remove screws so the time savings and convenience of camlocs isn't all that that much better.
Thanks Bob, I plan to use the nut-plate method on the nose section to get better coverage. Good to hear it may be actually better.
Quote:
Originally Posted by NDrv8r View Post
I have floaters all the way on the top. Doing it again, I would probably use screws.
I have had 2 issues with the floaters.
1. I have had several of the self adjusting mechanisms fail even after making sure the ball is aligned in its slot.
2. I have had several of the floaters fall out of their retainers.
Thanks for adding to the collective knowledge.

Thanks ALL for helping to get this documented. It is great to learn from the experience of others. I just hope my plane turns out half as good as yours.
__________________
Bill

RV-7
Lord Kelvin:
“I often say that when you can measure what you are speaking about,
and express it in numbers, you know something about it; but when you
cannot measure it, when you cannot express it in numbers, your knowledge
is of a meager and unsatisfactory kind.”
Reply With Quote
  #18  
Old 04-19-2014, 08:30 AM
NBowers NBowers is offline
 
Join Date: Dec 2006
Location: Leesburg, FL
Posts: 89
Default Floaters and Worn Holes

Quote:
Originally Posted by HIIFLY View Post
I am using the Skybolt system on my RV-8 for 135 hrs now and have No Problems with them . I have Floaters on the Firewall and Non Floaters on the seam between the upper cowl and lower cowl . I also have one #8 screw on each air in let outer and 3ea. #8 screws to the spinner side . It works well for me . That being said ------ if I were to do it again I think I would not use the Floaters on the Lower cowl verticle lt. & rt. Sides , I would use Vans Hinges and pins here only ! I think it would be easier to put the lower cowl in place drop the the pins streight down and it is all firmly in place ! Then use the Skybolt fasteners to finish the attachment of the cowl , butta bing / butta bang !
Skybolt just introduced our new adjusting floating receptacle that uses a clip retained cage versus our old fold over ear cage. We now perform a variety of tests on everything we make that goes far beyond Mil 5591 or NASM5591 that includes push out tests (200% over the minimum) and vibratory fatigue tests, to name a few.

We also have introduced our new DiamondHead Phillips fastener with a 42Rc hardness. What this means is that these studs will not gall, something that has been on my radar for years to resolve. In the process, we pushed the performance ratings for 300 stainless beyond the steel ratings.

The timing of this forum is great in that we are working on a grommet revision that surfaced in another application. We discovered some design limits that have been part of industry standard grommets for decades. Some work I have done with Cessna also focuses on worn holes and how we can eliminate or substantially subdue wear. Part of it has to do with the tiny radius on the ledge associated with the retainer and the retainer itself. And part of it has to do with the grommet undercut. We just solved all of this and I can immediately revise our Vans kits to take advantage of this. We are running these parts as we speak and will revise our kits in the next week. If you have a previous kit and want to swap grommets, email me at nedcbowers@yahoo.com and I will take care of it. In summary, I think we are are a good track to address cowling float and worn holes.

More innovations are on the way........Skybolt installation instructions are posted on our website. Call or email me with suggestions or questions. On another post, I want to talk about installation of flanges prior to engine installation.

Ned Bowers, Skybolt
Reply With Quote
  #19  
Old 04-19-2014, 02:46 PM
Greg Arehart's Avatar
Greg Arehart Greg Arehart is offline
 
Join Date: Jul 2007
Location: Delta, CO/Atlin, BC
Posts: 2,391
Default

Maybe too late for the original post, but for posterity, what I did was use hinges everywhere except on the firewall part of the top cowl. This makes taking off the top cowl very easy (a few screws for the hinge pin keepers and behind the spinner, and the floating skybolts on the firewall). Has worked well for almost 700 hours and 5.5 years now with little sign of excessive hole wear or slop in the cowl.

That's my experience anyway.

Greg
__________________
Greg Arehart
RV-9B (Big tires) Tipup @AJZ or CYSQ
N 7965A
Reply With Quote
  #20  
Old 04-19-2014, 03:48 PM
DonFromTX's Avatar
DonFromTX DonFromTX is offline
 
Join Date: Oct 2010
Location: La Feria Texas
Posts: 3,822
Default

On a Viking cowl for an RV12, that little dogleg at the firewall gets to be pretty busy with the Skybolts!
[IMG][/IMG]
__________________
A&P, PP-SEL, Pathological Flier, EAA Technical Counselor
EAA Chapter 595 President,http://www.595.eaachapter.org/index.htm
Retired US Army Officer
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 04:14 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.