|
-
POSTING RULES

-
Donate yearly (please).
-
Advertise in here!
-
Today's Posts
|
Insert Pics
|

02-07-2013, 07:42 AM
|
 |
|
|
Join Date: Sep 2012
Location: Omaha, NE (KMLE)
Posts: 2,247
|
|
Biggest oops so far
I bought my -7A with the empennage mostly complete, so I get to make my newbie mistakes on the wing. How exciting!
When I riveted the wing ribs to the rear spar, I had the skeleton on the wing stand. Big mistake. I couldn't see the bucking bar and a lot of rivets ended up way over-driven, plus some of the rib flanges weren't tight against the rear spar. The end result was a fair number of drilled-out rivets. I quickly figured out to do this sort of thing on the workbench from now on.
Most of them came out OK, and I bought a pneumatic squeezer that is turning out to be a FAR better solution for this. However, there is one place that I screwed it up pretty well. Fortunately it's the #13 rib -- naturally -- the last one before the wing tip. I ended up elongating the top and bottom holes of the rib and rear spar. A -4 rivet is not going to work in either of those holes.
I can think of two options to fix this: - I believe I could re-drill the holes for a couple of -5 rivets.
- I could also make a doubler plate to span all four rivets, and extend up the rib web where I'd set four more through the rib web and doubler plate. Then I would need to make two doublers for the other side of the rear spar -- I can't just use one because of W-724 that intersects that line of rivets. I'd need to put rivets on either side of the original holes.
What would y'all recommend?

__________________
Dale
Omaha, NE
RV-12 # 222 N980KM "Screamin' Canary" (bought flying)
Fisher Celebrity (under construction)
Previous RV-7 project (sold)
Last edited by DaleB : 02-07-2013 at 08:08 AM.
|

02-07-2013, 07:58 AM
|
|
|
|
Join Date: Jan 2006
Location: Vonore, TN
Posts: 369
|
|
-5 Rivet Sets
I had to drill out a few -4 rivets in the wing walk area and went with -5, but had to buy a -5 rivet set for the gun along with the rivets. If you use a squeezer you'll need a -5 cup set.
__________________
John Tierney
Vonore, TN
RV-7A - N777JT Flying
|

02-07-2013, 08:23 AM
|
|
|
|
Join Date: Feb 2005
Location: Blacksburg, VA
Posts: 149
|
|
I had an accident in the shop and had to replace the entire rear spar. Vans recommendation was to make doubler strips and place them on the interior of the wing ribs where needed. I don't recall if I needed any in the area of the flap brace.
For whatever reason, I had a difficult time setting the replacement rivets and will have to remove some of them- haven't gotten around to it yet, but am dreading this because it was such a stupid mistake resulting in a big hassle (skeleton fell off the wing stand).
|

02-07-2013, 09:40 AM
|
 |
|
|
Join Date: Jan 2007
Location: Battleground
Posts: 4,348
|
|
For the rib, it is perfectly acceptable to replace the flange. Cut it off, bend a new flange being sure to maintain proper bend radius, and rivet the new flange onto the rib using the same spacing as you have on the spar if you use 1/8" rivets. You want the part of the flange that you are riveting onto the rib web to be 1" wide. Now you have a clean flange.
For the Spar, if you go "by the book", when you use a doubler, you are supposed to have supporting rivets to each side of the repair. However, since your bad holes are on the end of the row, the only way to do that would be to make your double wider so you could put
one rivet to each side. That seems like a bit of overkill. I suspect a doubler tied to the good holes would be just fine, but....
When it comes to spars, the only authority is the airframe designer or manufacturer, so, once you decide on the repair, contact Van's. I believe they would sign off on a simple doubler but you might discuss the wider doubler idea with them too. It would not take much more time.
__________________
Smart People do Stupid things all the time. I know, I've seen me do'em.
RV6 - Builder/Flying
Bucker Jungmann
Fiat G.46 -(restoration in progress, if I have enough life left in me)
RV1 - Proud Pilot.
|

02-07-2013, 09:58 AM
|
|
|
|
Join Date: Dec 2006
Location: Coventry. England
Posts: 614
|
|
Rivetting
Dale..... a couple of tips.
If you are using a 3x gun hit the rivet for only about a second you will hear the strikes... ratatatat. Then check the rivet for setting it may need another 1/2 second squirt on the gun it may be OK. Also listen to the tone of the strikes... it changes when the rivet sets.
Also, to prevent things not being drawn together you can do a very short squirt on the gun so it perhaps hits the rivet only once, this will thicken it up so it fills the hole, then put a nut on the shop head side and do another one tap squirt on the gun, this will close any gap.... then you can do a 1 second sqirt to finally set the rivet.
Remember..... often a badly set rivet is often better than a drilled out one and elongated holes.
__________________
http://www.aerobuilder.blogspot.com
Steve Arnold
England
In completion stage of Loehle P5151
Built and now Flying G.BVLR Vans RV4
Rebuilt G.BDBD Tailwind
Rebuilt G BVTN Kitfox
Built G CDCD RV9A with WAM120
Riveted wings on Glastar G.LEZZ Now (G. SKUA)
|

02-07-2013, 10:20 AM
|
 |
|
|
Join Date: Sep 2012
Location: Omaha, NE (KMLE)
Posts: 2,247
|
|
Quote:
Originally Posted by WAM120RV
Dale..... a couple of tips.
If you are using a 3x gun hit the rivet for only about a second you will hear the strikes... ratatatat. Then check the rivet for setting it may need another 1/2 second squirt on the gun it may be OK. Also listen to the tone of the strikes... it changes when the rivet sets.
Also, to prevent things not being drawn together you can do a very short squirt on the gun so it perhaps hits the rivet only once, this will thicken it up so it fills the hole, then put a nut on the shop head side and do another one tap squirt on the gun, this will close any gap.... then you can do a 1 second sqirt to finally set the rivet.
Remember..... often a badly set rivet is often better than a drilled out one and elongated holes.
|
Thanks for the tips -- I've learned several lessons from this. - I need more light in the shop/garage/airplane factory. I have plenty of light over the work bench, but not NEARLY enough over the wing stand. I'll be adding an 8' fluorescent fixture this weekend. Maybe more than that.
- Wherever possible, I need to get parts on the bench instead of trying to make some other arrangement work. I knew that I could have moved the wing skeleton to the bench. I should have moved it to the bench. But it was on the stand, I was all pumped about having the stand there and the wing skeleton on it, and it would have taken half an hour to clear the bench off. So saving that half hour has now cost me a lot of time, and I needed to do it anyway. Now I have, and I'm wasting time with repairs I wouldn't be making if I'd taken the time to do it right the first time.
- If I can't see clearly that the parts are securely together, I need to slow down and fix that. Hoping they draw up tight doesn't work.
- Riveting parts that are not well supported so I can get good pressure on the rivet gun is a recipe for disaster.
__________________
Dale
Omaha, NE
RV-12 # 222 N980KM "Screamin' Canary" (bought flying)
Fisher Celebrity (under construction)
Previous RV-7 project (sold)
|

02-07-2013, 10:35 AM
|
 |
|
|
Join Date: Jan 2007
Location: Battleground
Posts: 4,348
|
|
Quote:
Originally Posted by DaleB
Thanks for the tips -- I've learned several lessons from this. - I need more light in the shop/garage/airplane factory. I have plenty of light over the work bench, but not NEARLY enough over the wing stand. I'll be adding an 8' fluorescent fixture this weekend. Maybe more than that.
- Wherever possible, I need to get parts on the bench instead of trying to make some other arrangement work. I knew that I could have moved the wing skeleton to the bench. I should have moved it to the bench. But it was on the stand, I was all pumped about having the stand there and the wing skeleton on it, and it would have taken half an hour to clear the bench off. So saving that half hour has now cost me a lot of time, and I needed to do it anyway. Now I have, and I'm wasting time with repairs I wouldn't be making if I'd taken the time to do it right the first time.
- If I can't see clearly that the parts are securely together, I need to slow down and fix that. Hoping they draw up tight doesn't work.
- Riveting parts that are not well supported so I can get good pressure on the rivet gun is a recipe for disaster.
|
You are a quick learner. Don't kick yourself too bad, this is a very minor mistake and you will have it repaired in less time than you spend worrying about it.
__________________
Smart People do Stupid things all the time. I know, I've seen me do'em.
RV6 - Builder/Flying
Bucker Jungmann
Fiat G.46 -(restoration in progress, if I have enough life left in me)
RV1 - Proud Pilot.
|

02-07-2013, 12:20 PM
|
 |
|
|
Join Date: Jun 2010
Location: McKinney, TX
Posts: 689
|
|
Quote:
Originally Posted by DaleB
Thanks for the tips -- I've learned several lessons from this.
|
One more thing you might consider. See if you can find a friend, or maybe your spouse, to enlist to help with the riveting. I'm a fairly short guy and my wingspan isn't great enough to reliably reach a lot of places. My wife helps with any major component riveting and I couldn't possibly build without her. As a team we make far fewer mistakes than when I try to go it alone.
__________________
Gil Brice
McKinney, TX EAA-1246
RV7 - Working on fuse, fuel, brakes etc...
|

02-07-2013, 12:58 PM
|
 |
|
|
Join Date: Mar 2007
Location: 45G, Brighton, MI
Posts: 1,867
|
|
Quote:
Originally Posted by DaleB
... I've learned several lessons from this. ...
|
That's what EAB is all about! 
__________________
Miles (VAF# 1238, Paid up as of 2018)
RV-7 TU 904KM (reserved)
Wings Fitted and Finish Kit on site
Construction Log
Picasa: Empennage Album, Wings Album, Fuselage Album
1955 Cessna 170B flying since 1982
'To get something you never had, you have to do something you never did.' -Unk.
|

02-07-2013, 01:10 PM
|
|
|
|
Join Date: Oct 2007
Location: Birmingham United Kingdom
Posts: 374
|
|
An3 bolt
A quick fix but slight over kill would be to drill the holes out with a #12 drill and put in a AN3 bolt.
__________________
RV7 G-PBEC Flying
RV10 Finishing
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 12:38 AM.
|