VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Model Specific > RV-7/7A
Register FAQ Members List Calendar Today's Posts

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-16-2012, 01:14 PM
TCONROY's Avatar
TCONROY TCONROY is offline
 
Join Date: Jul 2009
Location: Wilsonville, OR
Posts: 453
Default Forward tip-up frame question

I'm working on the canopy frame and have a question to ask fellow -7 builders. I've drilled and riveted the splice plate to the forward frame, but have NOT drilled the 1/4 holes for the hinge pins (release mechanism). I can't seem to get the skin to both have a 0.020" gap around the front AND for the left and right sides to sit perfectly above the fuselage side rails. If I shim for the 0.020 gap between the forward skin and canopy skin, the sides are at a little bit of an angle with probably a 0.5" gap, sitting above the fuselage side rails. If I set the sides correctly, I have a 0.05+ gap at the top portion between the two skins. It seems I can't achieve both. At one point I thought I had this right but it seems to have gotten off. Any suggestions?
http://rv7.conroyair.com/logindex/Fi...2012.06.06.htm
__________________
________
Trevor Conroy CFII, MEI
Airbus Pilot
N781TD
RV-7
First Flight - April 12, 2015

Construction Log
Reply With Quote
  #2  
Old 06-16-2012, 01:41 PM
Rupester Rupester is offline
 
Join Date: Dec 2005
Location: Mahomet, Illinois
Posts: 2,195
Default Can't help you specifically, but ...

... my advice is try not sweat some of those front canopy clearances too much. every time you complete another major task on the canopy assembly, it shifts a tiny bit and fits differently than before. I spent HOURS obsessing over those .020 and .030 clearances, only to find it changed every turn in the road. The most important thing is to install those non-provided (by Vans) canopy forward stops , or "snubbers", to prevent the gas cylinders from pushing the canopy forward when you install them. That can easily move your canopy .125 to .250 forward and ruin all your front edge clearance efforts to date.
__________________
Terry Ruprecht
RV-9A Tip-up; IO-320 D2A
S. James cowl/plenum
(Dues paid thru Nov '18)
Reply With Quote
  #3  
Old 06-17-2012, 04:14 AM
PIN 37 PIN 37 is offline
 
Join Date: Nov 2009
Location: Adelaide Australia
Posts: 218
Default

Quote:
The most important thing is to install those non-provided (by Vans) canopy forward stops , or "snubbers", to prevent the gas cylinders from pushing the canopy forward when you install them.
What is that about?? I am in the process of trying to make the canopy fit, but I have not heard about Snubbers???
__________________
Phil
LAME (Aust)
RV7 99% finished
Reply With Quote
  #4  
Old 06-17-2012, 07:48 AM
Rupester Rupester is offline
 
Join Date: Dec 2005
Location: Mahomet, Illinois
Posts: 2,195
Default

http://www.chadandbrittne.com/May%20...ay%2010-08.htm

Here's a pic from Chad's excellent website that shows the canopy "stops" or snubbers. They go on the top fuse rail, immediately fwd of the subpanel. The bolt they employ is adjusted tight up against the canopy fwd rail to prevent the gas cylinders from pushing the canopy fwd. Not difficult at all, and you can make them from scrap and a bolt or two from "Ace Aviation supply".
__________________
Terry Ruprecht
RV-9A Tip-up; IO-320 D2A
S. James cowl/plenum
(Dues paid thru Nov '18)
Reply With Quote
  #5  
Old 06-17-2012, 09:22 AM
rv9av8tr's Avatar
rv9av8tr rv9av8tr is offline
 
Join Date: Dec 2006
Location: Portland, OR
Posts: 827
Default Tip up canopy pics

I agree with the comments above. It's a floppy structure, even after it's complete. The resulting gap between the forward canopy skin and the forward fuse skin can be a problem spot based on accurate drilling of those 1/4" pin holes. I had binding problems between the two skins as the canopy opened. Ended up having to file back the canopy skin until it adequately cleared. You can address cosmetic issues when it's all said and done.

That top fuse skin is EXTREMELY tight along the left and right sides when getting clecos in.

The Van's folks commented to me slider or tipup, difficulty based on 1 to 10, the canopy is an 11. Ya just have to be patient and logically work through it.

My canopy pics can be seen here: https://picasaweb.google.com/mikerv9a/Canopy
__________________
Long-EZ built 1985 -> Sold 2007
RV-9A; N539RV First Flight: 7/2010
RV-8A N468DL 40 hr Flight Test Program
Building Log: www.mykitlog.com/n539rv
APRS Tracking: aprs.fi/n539rv
2017 Paid
Reply With Quote
  #6  
Old 06-18-2012, 08:18 PM
BSwayze's Avatar
BSwayze BSwayze is offline
 
Join Date: Jul 2007
Location: Molalla, Oregon
Posts: 955
Default

Quote:
Originally Posted by PIN 37 View Post
What is that about?? I am in the process of trying to make the canopy fit, but I have not heard about Snubbers???
I agree with Rupester. The installation of the gas struts messes up all your careful fitting work. I thought I'd give you a reference to how I did mine, too. Here's a link to my log page for this item:

Forward Canopy Stops

They made a dramatic difference in maintaining how the canopy fits after installing the gas struts. I made them from scrap that I had on hand. The bolts I used are Joint Connector Bolts found at a local hardware store. I added a layer of UHMW tape to the surface of each one to minimize scratching on the forward face of the frame. The extra holes are just lightening holes.



__________________
Bruce Swayze
RV-7A Standard Build
First flight November 3, 2019!
http://www.BrucesRV7A.com
Reply With Quote
  #7  
Old 06-18-2012, 11:12 PM
chunt0 chunt0 is offline
 
Join Date: Oct 2005
Location: Canton, MI
Posts: 76
Default Canopy

Some thoughts on the tip-up:

The canopy front skin probably is correctly trimmed and punched. That's logical since it is a single piece flat wrap. The weldments are multiple pieces jigged together and distorted from the welding process. No two are likely to be the same. If I is was starting over, I would focus on shimming/twisting/bending/splicing the weldments to fit the skin.

I needed a minimum .036 inch gap at the front of the skin to keep it from hanging up during opening. Even then, I had to carefully bevel both sheet metal edges to allow them to "shingle" a bit. In theory, it should be possible to tighten up that gap a little by nailing the height of the pivot pin holes just right.

The plans 9 11/16 inch dimension for the closed canopy gas strut length should be treated as a bare minimum. The strut toggles over center by about a quarter inch as it nears closure. If your rear attachments are too far forward, you will be bottoming out the struts during each opening/closing cycle. This forces the canopy frame to flex unnecessarily.

Van's drawing shows the rod ends of the struts forward. My last picture of their 7A shows they actually have their cylinder ends forward. Because of how the oil settles in the cylinders, they function much better that way--with a nice cushioning effect at the end of their travel .

Some people swear by the forward stop mod. Once everything was properly fitted and solidly riveted together, I found I didn't need them.
__________________
Charlie
RV-7A
Canton, MI
Reply With Quote
  #8  
Old 06-19-2012, 06:32 AM
LettersFromFlyoverCountry's Avatar
LettersFromFlyoverCountry LettersFromFlyoverCountry is offline
 
Join Date: Jan 2005
Location: St. Paul, MN.
Posts: 4,792
Default

I wrote this article on the canopy stops some years ago. I swear I took the canopy and canopy frame on and off the project 5,000 times and 4,999 of those times, it did not fit the same way when putting it back on.

I THINK -- and your mileage may vary -- that Van's has you adjusting the gap between the canopy skin and the top skin way too early in the process. If I do it again -- and someday I may do it again -- I'd wait until I was about to rivet the top skin on for the last time.

I also didn't like the gaps on the side much. They were OK when viewed from the outside, but from the inside they looked -- as Walter Tondu once famously said -- "like you could throw a cat through them." I ended up extending the sides with fiberglass pieces. So the bad thing about the canopy frame is it's not a very fun design. The good thing about it is you can play with it later to satisfy one's OCD.

I would also be more careful -- and it's not like I wasn't careful to begin with -- in drilling those 1/4" hinge pin holes because that had more to do with the fit of the canopy than anything else I did. In my case, I got it just wrong enough to end up with a higher gap from canopy-skin-to-top-skin on one side, which I only recently solved by building the area up.

Oh, one other thing on those canopy stops. They go in an area where you're going to need to get in with a bucking bar when you rivet the top skin on for good. So you might want to build a little clearance in there.
__________________
Bob Collins
St. Paul, MN.
Blog: Letters From Flyover Country
RV-12iS Powerplant kit
N612EF Builder log (EAA Builder log)

Last edited by LettersFromFlyoverCountry : 06-19-2012 at 06:43 AM.
Reply With Quote
  #9  
Old 06-19-2012, 06:38 AM
Rupester Rupester is offline
 
Join Date: Dec 2005
Location: Mahomet, Illinois
Posts: 2,195
Default

Charlie is right about the importance of locating the strut rear attach. Nevertheless, the canopy stops are easy and cheap to install, and can be a big benefit depending on the specifics of your install. And BYW, Bruce's canopy stops are the snazziest I'VE seen ... most of us just hacked up a small piece of angle.
__________________
Terry Ruprecht
RV-9A Tip-up; IO-320 D2A
S. James cowl/plenum
(Dues paid thru Nov '18)
Reply With Quote
  #10  
Old 06-19-2012, 10:42 AM
TCONROY's Avatar
TCONROY TCONROY is offline
 
Join Date: Jul 2009
Location: Wilsonville, OR
Posts: 453
Default

What do you all think of the edge distance here? I'm not totally thrilled with it but I understand it is common and doesn't seem to be a big issue. I don't have the exact dimension right now. The other one is a bit better.
__________________
________
Trevor Conroy CFII, MEI
Airbus Pilot
N781TD
RV-7
First Flight - April 12, 2015

Construction Log
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 01:32 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.