|
-
POSTING RULES

-
Donate yearly (please).
-
Advertise in here!
-
Today's Posts
|
Insert Pics
|

07-25-2011, 08:28 AM
|
|
|
|
Join Date: Mar 2005
Location: St. George
Posts: 973
|
|
RE: Not Sure
Don't know the answer to that other than I have heard (old age setting in) and can't remember the guru that said it the overall long life of the engine is enhanced by staying above 60 and below 90 in cruise????? I do know ECi put 60 as a minimum cruise pressure.
Maybe Mahlon or one of the other gurus can give the answer
Frank @ 1L8 ... Flying ...
|

07-25-2011, 08:31 AM
|
|
|
|
Join Date: Mar 2005
Location: St. George
Posts: 973
|
|
RE: PIX
Quote:
Originally Posted by rocketbob
True, and that makes two poor designs...
On my rocket I have removed the expensive vernatherm and put the oil cooler bypass plunger and spring, and will control the oil temps manually with a ball valve.
|
Hi Bob
Do you have pictures and diagrams and parts list for this option. And have you flown your rocket ....
Frank @ 1L8 ... RV7A... Flying
Last edited by fstringham7a : 07-25-2011 at 08:54 AM.
|

07-25-2011, 08:59 AM
|
|
|
|
Join Date: Aug 2006
Location: Twin Falls, ID
Posts: 683
|
|
Frank, What is your oil pressure at idle hot? Do you have the vacuum pump housing on your engine? Don
__________________
RV 7 N212MD Flying as of 12/22/2007
Backcountry/TCOW Super Cub flying 03/12/2011
Next project?
|

07-25-2011, 09:32 AM
|
 |
|
|
Join Date: Jun 2006
Location: 8I3
Posts: 3,564
|
|
Quote:
Originally Posted by fstringham7a
Hi Bob
Do you have pictures and diagrams and parts list for this option. And have you flown your rocket ....
Frank @ 1L8 ... RV7A... Flying
|
No pics of the valve yet since I don't have it hooked up and haven't flown but got the idea from Larry Vetterman. I do have the bypass plunger installed. The ball valve goes on the oil cooler line and is controlled from the cockpit.
__________________
Please don't PM me! Email only!
Bob Japundza CFI A&PIA
N9187P PA-24-260B Comanche, flying
N678X F1 Rocket, under const.
N244BJ RV-6 "victim of SNF tornado" 1200+ hrs, rebuilding
N8155F C150 flying
N7925P PA-24-250 Comanche, restoring
Not a thing I own is stock.
|

07-25-2011, 10:17 AM
|
 |
|
|
Join Date: Nov 2006
Location: Boise, ID
Posts: 1,095
|
|
Quote:
Originally Posted by fstringham7a
Don't know the answer to that other than I have heard (old age setting in) and can't remember the guru that said it the overall long life of the engine is enhanced by staying above 60 and below 90 in cruise????? I do know ECi put 60 as a minimum cruise pressure.
Maybe Mahlon or one of the other gurus can give the answer
Frank @ 1L8 ... Flying ...
|
Where did you read that? I can't find any operating instruction documents from ECI at all. I was told to use the Lycoming materials since they should be the same.
__________________
Sonny W
Boise, Idaho
RV-7A Flying!
|

07-25-2011, 10:43 AM
|
|
|
|
Join Date: Jan 2005
Posts: 1,025
|
|
25 psi is min idle oil pressure or bottom red line
55-95 is cruise oil pressure or green arch ( used to be 60-90 but Lycoming changed it a few years back)
115 is max cold oil pressure or top red line.
I would be fixing it, if it had less then 60psi for oil pressure, in cruise, if it were mine.
Good Luck,
Mahlon ?The opinions and information provided in this and all of my posts are hopefully helpful to you. Please use the information provided responsibly and at your own risk."
|

07-25-2011, 12:00 PM
|
|
|
|
Join Date: Mar 2005
Location: St. George
Posts: 973
|
|
RE:Vac Area
Quote:
Originally Posted by yakdriver
Frank, What is your oil pressure at idle hot? Do you have the vacuum pump housing on your engine? Don
|
Hi Don
If I am reading your question correctly I have the SD-8 aux alternator on the Vac pad....
Oil pressure at start up (old spring) was 81 and would be at or about 75 to 80 at t/o. New Spring it was 89 at start up and can't remember the run up temp or pressure and at t/o hit 108
Frank
|

07-25-2011, 12:20 PM
|
|
|
|
Join Date: Mar 2005
Location: St. George
Posts: 973
|
|
RE: Info
Quote:
Originally Posted by lostpilot28
Where did you read that? I can't find any operating instruction documents from ECI at all. I was told to use the Lycoming materials since they should be the same.
|
It took me a while but I finally found the info on the ECi web site. On the ECi Home page there is a square info position on the left side that says Titan EXP....... http://www.eci.aero/ ...... which takes you to http://www.eci.aero/exp/index_exp.aspx ...... then on the left is a box EXP KIT Egines and hit either Over view Brochure or Engine Comparison Chart.
http://www.eci.aero/exp/eng_comparisons_chart.pdf
http://www.eci.aero/exp/eng_comparisons_brochure.pdf
As far as operating instructions Robbie Attaway, local RV drivers, and info from VAF is what schooled me!!!!!!!!!! Plus this info from ECi
http://www.eci.aero/pages/tech.aspx#breakin
Sonny, I hope this helps. So now the race is on who will get their plane dialed in first. I personally hope it is you so I can learn from you.
Frank @ 1L8 ...RV7A... Flying kinda!!!!!!!!!!!!!!!!!!!!!!
|

07-25-2011, 01:02 PM
|
|
|
|
Join Date: Aug 2006
Location: Twin Falls, ID
Posts: 683
|
|
Quote:
Originally Posted by fstringham7a
Hi Don
If I am reading your question correctly I have the SD-8 aux alternator on the Vac pad....
Oil pressure at start up (old spring) was 81 and would be at or about 75 to 80 at t/o. New Spring it was 89 at start up and can't remember the run up temp or pressure and at t/o hit 108
Frank
|
Reason I asked is that I had oil pressure problems with my engine. My pressure would start out 95psi at 100 degrees oil temp, 85psi at 180 and would fall to 50psi at 230. Idle pressure was 15psi hot. Caused a spun rod bearing. The vacuum housing was on the case but without a gear in it letting the oil bypass. Now start up and take off 85psi, lowest it gets in cruise is 78psi at 220 temp. Idle 40-50psi. Sounds like you might have a missing oil galley plug. Don
__________________
RV 7 N212MD Flying as of 12/22/2007
Backcountry/TCOW Super Cub flying 03/12/2011
Next project?
|

07-25-2011, 09:20 PM
|
 |
|
|
Join Date: Nov 2006
Location: Boise, ID
Posts: 1,095
|
|

Quote:
Originally Posted by fstringham7a
It took me a while but I finally found the info on the ECi web site. On the ECi Home page there is a square info position on the left side that says Titan EXP....... http://www.eci.aero/ ...... which takes you to http://www.eci.aero/exp/index_exp.aspx ...... then on the left is a box EXP KIT Egines and hit either Over view Brochure or Engine Comparison Chart.
|
Thanks, Frank. I don't know why ECI doesn't make their own manuals...would make sense, no?
As for a solution, I hope this does make a difference...I'm running out of ideas on what to do next. I really don't want to cut holes for those louvers! 
__________________
Sonny W
Boise, Idaho
RV-7A Flying!
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 06:45 AM.
|