VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #11  
Old 02-27-2009, 04:40 PM
rvbuilder2002's Avatar
rvbuilder2002 rvbuilder2002 is offline
 
Join Date: Jul 2005
Location: Hubbard Oregon
Posts: 9,035
Default Another data point...

I am not sure at this point how I feel (or should feel) about an oxygen tank in the tail cone adjacent to the battery, but it does bring to mind a recent Lancair IV accident that would make me have to really think about it for a while.

Here is a link to the salvage sale page with photos http://www.aigaviation.com/aviations...x?faano=N731SJ

Link to NTSB prelim report
http://www.ntsb.gov/ntsb/brief.asp?e...22X01515&key=1

Short story...Battery fire in aft tailcone. I don't know where the emergency O2 bottle (I would assume it has one) for a Lancair IX P is located, but I have a feeling it was not in the tail cone (on this airplane at least).
__________________
Opinions, information and comments are my own unless stated otherwise. They do not necessarily represent the direction/opinions of my employer.

Scott McDaniels
Van's Aircraft Engineering Prototype Shop Manager
Hubbard, Oregon
RV-6A (aka "Junkyard Special ")
Reply With Quote
  #12  
Old 02-27-2009, 06:30 PM
Bob Brown's Avatar
Bob Brown Bob Brown is offline
 
Join Date: Dec 2005
Location: Somewhere in a motorhome
Posts: 581
Default Security

As a former EMT who has come upon a lot of accidents involving high speed impacts of gas cylinders and batteries, and who used to travel with oxygen cylinders along a lot of rough country roads...I think the most important thing is to make sure the two systems are secured well. The tail section of an airplane is usually the part that survives impacts the best...and I've seen a number of wrecked Cessna's with batteries in the back where the battery was OK...untouched even, where the occupants were not OK. One of the safety rules of storing high pressure gas cylinders (oxygen or CO2 or argon or whatever) is to always make sure the cylinder is secured well, ostensibly to prevent an impact from damaging or breaking the valve. The cylinder itself is pretty bulletproof, but you because of its mass, you don't want it rattling around. I think the same goes for a battery...especially the Odyssey's most of us are using. They are pretty well built, they don't tend to leak or outgas like the old timey wet cell batteries...but they do need to be very secure, as do their connections! I'd be a lot more concerned about a fuel leak in fuel lines in the tunnel and in proximity to static electrical discharges than I would be some O2 floating around in an (unfortunately!) well ventilated RV cockpit. Hey, at least we're not building ash trays in our RV's like a few of my old '60's era Cessna's had!!!

Most STC'd aftermarket O2 systems for certified aircraft put the cylinder in the tail (where the battery is on 24V Cessnas). I plan on putting my O2 cylinder in the tail, for both practical and CG reasons...consulting the manufacturer for proper selection of high quality lines, sealing them properly and inspecting the system regularly...the same as I do with the fuel lines that are all around me in the cockpit...

In my -7, I strap a portable O2 cylinder to the back of the flap motor brace...and I've often thought about O2 in the cockpit as I unplug my various handheld devices from the 12V power source or run the flap motor...but so far, no kaboom.

Like all the hazards we fly with, this one should be identified, examined, analayzed and dealt with properly.
__________________
RV7A-QB, RV-10
Reply With Quote
  #13  
Old 02-27-2009, 09:03 PM
rene@felker.com's Avatar
rene@felker.com rene@felker.com is offline
 
Join Date: Jan 2006
Location: Ogden Utah
Posts: 161
Default

Quote:
Originally Posted by Auburntsts View Post
To change gears a bit, I'm interested in the installation on the other end of the system.

-- If you are or planning to use bulkhead style outlets, where are you mounting them? I plan on having both and overhead and a center console so there's lots of mounting possibilites but having never used O2 I don't know what is a practical solution. For example, I could easily mount outlets in the overhead, but would having O2 tubes hanging down when in use be a nuisance?

-- What kind of tubing (metal vs plastic) are you using to plumb the system from the tank to the outlets?
I used the mountain high system and it has pulse demand distributors for each station. They are not small, you need to consider the system you are using, since it will drive where you can put the fittings.

The MH system comes with plastic tubing, each to work with.......

The MH system is.......$$$$$$ >$6,000
__________________
Rene' Felker
N423CF RV-10 Flying
Reply With Quote
  #14  
Old 02-28-2009, 12:45 PM
bruce1369 bruce1369 is offline
 
Join Date: Mar 2007
Location: Arco, Idaho
Posts: 14
Default Oxygen systems

I have been working/using oxygen systems in aircraft and industrial equipment since 1978.

I did not cite any examples of problems because I knew the posters would make up all KINDS of excuses/reasons why this will be OK.

If you are flying your aircraft and the battery causes a fire in close proximity to your O2 system, you will die.

So, if you think you are lucky, proceed. Good luck to you.
Reply With Quote
  #15  
Old 02-28-2009, 09:21 PM
frazitl's Avatar
frazitl frazitl is offline
 
Join Date: Jan 2005
Location: Las Vegas, NV
Posts: 488
Default

Building a 7a but my previous ride was a 91 Mooney TLS~ BRAVO. MOONEY installed two 24V batteries within two feet of a 115 cu ft kevlar O2 bottle. Contactots and remote avionics in the same compartment aft of the baggage compartment. Combustion requires fuel, O2 and ingition - all in the same place at the same time. I would not consider an aux fuel tank on the same location. Pls excuse the blackberry mispellings...
__________________
Terry F.
RV 7A N457RV
250 hours and lovin it!
Southern Nevada EAA Chapter 1300 - www.eaa1300.org

Paid VAF 03/17
Reply With Quote
  #16  
Old 02-28-2009, 11:15 PM
Bob Brown's Avatar
Bob Brown Bob Brown is offline
 
Join Date: Dec 2005
Location: Somewhere in a motorhome
Posts: 581
Default

It was a given that some people will not get over having O2 that close to a battery or an electrical connection of any type...but in the certified aircraft world, just take a look at how these systems have been installed for 20 years. Find a few examples of O2 systems blowing up and let's analyze them...I looked for some examples and couldn't find them. I'm not trying to be in denial here, I'm asking for input. If you really think that its unwise to have an O2 system in an aircraft, I don't think that's a view supported by problems observed in certified installations. So lets make ours like certified installations...that was my point.
__________________
RV7A-QB, RV-10
Reply With Quote
  #17  
Old 06-07-2010, 06:18 PM
flion's Avatar
flion flion is offline
 
Join Date: Dec 2007
Location: Flagstaff, AZ
Posts: 2,653
Default

Having decided long ago to locate the oxygen cylinder in the tail cone, I don't wish to reopen that part of the debate. I do, however, have another issue which I'd like opinions on, especially DAR opinions (listening, Mel?). Because I have the air conditioning system on a tray above the longerons, I can't do a vertical install like Randy did (see link on iflyrv10). No problem; plenty of room to do a fore/aft install. But I wanted the cylinder on the right side of the fuselage so I'd have easier access to the battery and master solenoids and I can easily run the O2 filler where I want. But then I looked at the TruTrak servo and wondered about acceptable clearance. Below is a photo with the cylinder in position as far left as I can and the servo held in position above the bracket; it would actually be one inch lower. The lateral clearance is two inches as shown by the ruler. You are looking aft at the bottom of the tail cone.



I can't imagine anything closing that lateral distance that wouldn't be as catastrophic already as the servo hitting the cylinder, so I'm not really worried about danger. But I want to be sure it will pass inspection in that location. Should I be worried?
__________________
Patrick Kelley - Flagstaff, AZ
RV-6A N156PK - Flying too much to paint
RV-10 14MX(reserved) - Fuselage on gear
http://www.mykitlog.com/flion/
EAA Technical Counselor #5357
Reply With Quote
  #18  
Old 06-07-2010, 07:11 PM
RNewman RNewman is offline
 
Join Date: Oct 2007
Location: Emmaus PA
Posts: 55
Default oxygen in rv-10

I'm just finishing up my installation, MH system in the RV-10, mounted in tailcone, horizontal orientation. Here's a link to my picasa site.

http://picasaweb.google.com/rcnewman64/OxygenSystem#


Bob Newman
40176,
TCW Technologies
Reply With Quote
  #19  
Old 06-07-2010, 08:14 PM
flion's Avatar
flion flion is offline
 
Join Date: Dec 2007
Location: Flagstaff, AZ
Posts: 2,653
Default

Bob, no offense, but I don't find your installation acceptable. The datasheet that came with the mounting system lists the G load limits in all directions and the lateral load limit is very small. You've got it aligned in the vertical direction, which is where most of the loads go when maneuvering. I think you should add support under the bottle; perhaps build a shelf supported diagonally to the side or the bottom. I've considered the same but prefer to follow the KISS rule and keep the additional structure minimal.
__________________
Patrick Kelley - Flagstaff, AZ
RV-6A N156PK - Flying too much to paint
RV-10 14MX(reserved) - Fuselage on gear
http://www.mykitlog.com/flion/
EAA Technical Counselor #5357
Reply With Quote
  #20  
Old 06-08-2010, 11:06 AM
RNewman RNewman is offline
 
Join Date: Oct 2007
Location: Emmaus PA
Posts: 55
Default

Thanks for the advice, I did look at this in deciding the mounting orientation and the bracket I designed. The side loading allowed by the MH instructions is 2-4 Gs, I added large fender washers, (not shown in photo's) to the back side of my bracket to prevent pull through the the 8- 1/4" bolts. With the RV-10 operational G limit of 3.8, I considered this to a satisfactory install for a non-aerobatic plane. So there's my logic, right out on the table.


Thanks,
Bob
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 06:55 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.