|
-
POSTING RULES
-
Donate yearly (please).
-
Advertise in here!
-
Today's Posts
|
Insert Pics
|
08-22-2008, 08:42 AM
|
 |
|
|
Join Date: Feb 2005
Posts: 1,082
|
|
Adhesive for Interior Panels
I tried with miserable results to use 3M 77 spray adhesive to attach my interior panels that are vinyl covered corrugated plastic boards. The vinyl sticks great with the spray glue to the plastic but will not stay attached to the aluminum.
What are others using to attach their interior panels to the aluminum that will not corrode it over time?
__________________
Mike
JAMES AIRCRAFT.com
Flying - RV8 Hot Rod "Drone Killer"
Flying - RV8 "Look'n Good"
RV4 - FAST & FUN! Rebuilt, Flown, Sold
RV-7A Built, Flown, Sold
|
08-22-2008, 09:00 AM
|
 |
|
|
Join Date: May 2005
Location: Canby, Oregon
Posts: 1,786
|
|
hummmm...
I had the same problem. I hope that the Shoe Goo that I used won't effect the AL.
Kent
__________________
Kent Byerley
RV9A N94KJ - IO320, CS, tipup
AFS 3500, TT AP, FLYING....
Canby, Or
|
08-22-2008, 09:08 AM
|
 |
|
|
Join Date: Jan 2005
Location: 57AZ - NW Tucson area
Posts: 10,011
|
|
Airtex
Quote:
Originally Posted by Capflyer
I tried with miserable results to use 3M 77 spray adhesive to attach my interior panels that are vinyl covered corrugated plastic boards. The vinyl sticks great with the spray glue to the plastic but will not stay attached to the aluminum.
What are others using to attach their interior panels to the aluminum that will not corrode it over time?
|
Airtex trim adhesive works great.
DURASEAM TRIM CEMENT
Bottom of the page.... http://www.airtexinteriors.com/catalogue/misc.htm
It's a old style contact cement full of VOCs... which seems to be better than the newer stuff you can buy at the hardware store... 
It's even made for airplanes, and works well on the vinyl of my Tiger in the AZ heat.
__________________
Gil Alexander
EAA Technical Counselor, Airframe Mechanic
Half completed RV-10 QB purchased
RV-6A N61GX - finally flying
Grumman Tiger N12GA - flying
La Cholla Airpark (57AZ) Tucson AZ
|
08-22-2008, 09:20 AM
|
 |
Senior Curmudgeon
|
|
Join Date: Sep 2005
Location: Dayton Airpark, NV A34
Posts: 15,408
|
|
Adhesive backed self stick velcro strips.
By the way, clean the alum with mek, or acetone first.
__________________
Mike Starkey
VAF 909
Rv-10, N210LM.
Flying as of 12/4/2010 
Phase 1 done, 2/4/2011
Sold after 240+ wonderful hours of flight.
"Flying the airplane is more important than radioing your plight to a person on the ground incapable of understanding or doing anything about it."
|
08-22-2008, 11:04 AM
|
|
|
|
Join Date: Jan 2005
Location: Peshtigo, Wisconsin
Posts: 767
|
|
I had similar problems getting 3M 77 to work as well. Switched to 3M 90 and it worked great.
__________________
Jeff Orear
RV6A N782P
Peshtigo, WI
|
08-22-2008, 12:54 PM
|
 |
|
|
Join Date: Jan 2005
Location: SC
Posts: 12,887
|
|
Are you gluing these panels to the skins or to Velcro pads so they can be removed for future inspection?
There is a chance that by gluing your covering right to the aluminum, you could trap water, oil, and dirt there causing future problems.
By mounting them on Vecro tabs, you can remove the covering for inspectiona and future wire runs.
Just a thought.
__________________
Bill R.
RV-9 (Yes, it's a dragon tail)
O-360 w/ dual P-mags
Build the plane you want, not the plane others want you to build!
SC86 - Easley, SC
www.repucci.com/bill/baf.html
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 04:05 AM.
|
Linear Mode
