VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics


Go Back   VAF Forums > Main > RV General Discussion/News
Register FAQ Members List Calendar Today's Posts

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 07-29-2008, 09:27 AM
Webb's Avatar
Webb Webb is offline
 
Join Date: Oct 2007
Location: Jackson, MS
Posts: 1,262
Default Access door in wheel fairings

I looked but didn't find anything about an access door in the wheel fairings for routine pressure checks of the tires.

With all the discussion about tire pressure on the nose wheel to prevent an accident, I began thinking that I would like to have an easy way to check pressures on all tires without pulling the the wheel pants off. Down side is you don't visually inspect the assembly each time but easy pressure check would be the upside.

Since I'm close to finishing the wheel fairings, now is the time.

I had 2 thoughts.

#1 - It would be very easy to cut a small door, hinge and back frame it for support with a latch / camlock fastner / placenut & screw.

#2 - Cut a 1" hole like the one used in the front fairing for the tow bar that would allow you to put a gauge/filler on the stem. Faster and easier than option #1 but tight quarters to get the valve stem screw top on/off.

Good ideal - bad ideal? Has anybody done either?
__________________
Webb Willmott
Jackson, MS
N32WW
Reply With Quote
  #2  
Old 07-29-2008, 09:35 AM
664781 664781 is offline
 
Join Date: Jan 2005
Location: Powder Springs, Ga
Posts: 309
Default

Webb,
I did #2 and take the stem cap off with a 1/4 drive socket. No problem...
__________________
Kurt Lohmueller A&P, DAR
Powder Springs, Ga
RV6A "Kurt's Toy" - Flying
RV12 - Flying - Sold
Reply With Quote
  #3  
Old 07-29-2008, 09:45 AM
erich weaver's Avatar
erich weaver erich weaver is offline
 
Join Date: Aug 2006
Location: santa barbara, CA
Posts: 1,682
Default

Check out http://www.aircraftextras.com/ - scroll down until you find "valve extension"

works for me

erich
Reply With Quote
  #4  
Old 07-29-2008, 09:51 AM
Webb's Avatar
Webb Webb is offline
 
Join Date: Oct 2007
Location: Jackson, MS
Posts: 1,262
Default Hole location

Quote:
Originally Posted by 664781 View Post
Webb,
I did #2 and take the stem cap off with a 1/4 drive socket. No problem...

Where did you put the hole?

I also noticed on Aircraftspruce, Camloc has a 1" plate cover that is spring loaded:

http://www.aircraftspruce.com/catalo...ccessdoors.php)

Not sure I want to spend 75 bucks for those if not really needed but look nice. Could always add later since the hole is a 1 incher.
__________________
Webb Willmott
Jackson, MS
N32WW
Reply With Quote
  #5  
Old 07-29-2008, 10:03 AM
Ironflight's Avatar
Ironflight Ironflight is offline
VAF Moderator / Line Boy
 
Join Date: Jan 2005
Location: Dayton, NV
Posts: 12,256
Default Or....

I didn't go with the access holes because I was to lazy to figure out where they would go. It takes me about 30 seconds to get the front half of the wheel pant off - about as much time as I used to spend hunting for the tire valve through the holes on my old Grumman. Using Michelin Air Stops, I only have to check/add air about once every three months or so, and I generally find that I have the front halves off to check tire or brake wear in that time anyway.

It is certainly not as trick as having access doors/holes, but I haven't found that I miss them.

Paul
__________________
Paul F. Dye
Editor at Large - KITPLANES Magazine
RV-8 - N188PD - "Valkyrie"
RV-6 (By Marriage) - N164MS - "Mikey"
RV-3B - N13PL - "Tsamsiyu"
A&P, EAA Tech Counselor/Flight Advisor
Dayton Valley Airpark (A34)
http://Ironflight.com
Reply With Quote
  #6  
Old 07-29-2008, 11:21 AM
John Clark's Avatar
John Clark John Clark is offline
 
Join Date: May 2005
Location: Santa Barbara, CA
Posts: 1,324
Default Tire and brake inspection...

...is just as important as tire pressure. A couple of minutes spent once a month can avoid a lot of problems.

John Clark
RV8 N18U "Sunshine"
KSBA
Reply With Quote
  #7  
Old 07-29-2008, 11:37 AM
Rick6a's Avatar
Rick6a Rick6a is offline
 
Join Date: Jan 2005
Location: Lake St. Louis, MO.
Posts: 2,346
Default

Quote:
Originally Posted by Webb View Post
I looked but didn't find anything about an access door in the wheel fairings for routine pressure checks of the tires......
I installed flush mounted spring loaded Camloc type wheel pant access covers. They are very easy to install using two AD4 rivets and a retrofit can be done anytime. The photo in the link shows INSIDE detail of a cover.

http://www.aircraftspruce.com/catalo...ccessdoors.php

Check around for competitive pricing. A few years ago, I bought a number of them as "new surplus" from a vendor at the AirVenture Flymart for $5 each.

__________________
Rick Galati
RV6A N307R"Darla!"
RV-8 N308R "LuLu"
EAA Technical Counselor
Reply With Quote
  #8  
Old 07-29-2008, 11:44 AM
Geoff
 
Posts: n/a
Default No access doors

Quote:
Originally Posted by Ironflight View Post
Using Michelin Air Stops, I only have to check/add air about once every three months or so
Maybe I'm just extremely lucky, but I've been flying since last September and in 70 hours I've never had to add any air. They've dropped maybe 1-2 psi in 10 months. I'm using whatever tires/tubes Vans supplied with the kit.
Reply With Quote
  #9  
Old 07-29-2008, 08:36 PM
L.Adamson's Avatar
L.Adamson L.Adamson is offline
 
Join Date: Apr 2005
Location: KSLC
Posts: 4,021
Default

I put the 1" hole where the valve is in the "six o:clock" down position. I marked the tire with a red line to find it easy. Also use a valve extention I bought from NAPA.

L.Adamson -- RV6A
Reply With Quote
  #10  
Old 07-30-2008, 12:25 AM
Pirkka Pirkka is offline
 
Join Date: Feb 2006
Location: Europe, Finland (EFTU)
Posts: 542
Default

Quote:
Originally Posted by Webb View Post
I looked but didn't find anything about an access door in the wheel fairings for routine pressure checks of the tires.
I did looked as well...

http://www.vansairforce.com/communit...ad.php?t=17804
http://www.vansairforce.com/communit...ead.php?t=2966
http://www.vansairforce.com/communit...ad.php?t=27685

Hope these helps!
__________________
Pirkka

- RV-7 -
Tail: Waiting for fiberglass.
Wings: Some priming left, then lot of riveting.
QB Fuse + Finishing kit: in crates.
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 12:35 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.