VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 03-13-2007, 10:38 PM
greggrv7a greggrv7a is offline
 
Join Date: Jan 2005
Posts: 11
Question Cowling / Prop Question

Wondering if anyone with a three bladed prop can help with a problem I am having with installing my bottom cowling on my 7A. I would appreciate any help / pictures from anyone who has had the same problem.

Tnxs,

Gregg
Reply With Quote
  #2  
Old 03-14-2007, 04:48 AM
db1yg's Avatar
db1yg db1yg is offline
 
Join Date: Mar 2006
Posts: 629
Default

Gregg,

I have a 3 blade Catto on my RV9a. To mount the bottom cowl the slot in the cowl for the nose gear has to be cut forward more than the two blade equiped RV. Cut a little at a time to insure you get just the minimum amount with some additional for gear flex. Note that the cowl is best mounted at a slight angle with one side lower than the other until the blades are cleared--then straight on. Two people are required--especially when initially fitting. Put some tape on the edges of the prop to avoid scratches from the hinges between top and bottom cowl (the horizontal hinge) as it passes by the blades. To cover and reinforce the lower cowl I extended forward my nose gear leg to cowl fairing by about 6 inches. I have some pics somewhere--let me know if you need them.

Hope this helps!!

Cheers,

db
__________________
Dave B.
RV9a/ECiIO360/James Cowl/WW RV200 Prop
Flying since 3/06 and still smiling!!!
Reply With Quote
  #3  
Old 03-14-2007, 10:56 AM
steveciha steveciha is offline
 
Join Date: Jun 2005
Posts: 89
Default

I remember when i started to fit my 3 blade whirlwind prop. I thought,"this is never going to work" but it will. just cut the slot longer. There is a definite install, remove scheme that you will find works for you to get the cowl off and on. After a short time i caught on to doing it myself with no problem. I did make a nice fiberglass fairing to cover the long nose gear slot in the cowl. It helps to stiffen up the bottom cowl in the nose gear area. I can take a picture for you if you like. It will be a little while though.

steve ciha
Reply With Quote
  #4  
Old 03-14-2007, 01:32 PM
pierre smith's Avatar
pierre smith pierre smith is offline
 
Join Date: Jan 2005
Location: Louisville, Ga
Posts: 7,840
Default Funny you should ask.....

Hi Gregg,
We had the same issue with ours but we have the fairings-etc upper intersection fairing and it's really long with one nut plate/screw at the very front end. I finally had to cut the slot as near the nutplate as I dared. We still have remove that intersection fairing to allow the bottom cowl to drop as far down as possible and with a helper, raise the rear as high as practical while you slide it carefully forward. It's tricky but it can be done without scratching the prop if you duct-tape the prop first.

Regards,
__________________
Pierre Smith
RV-10, 510 TT
RV6A (Sojourner) 180 HP, Catto 3 Bl (502Hrs), gone...and already missed
Air Tractor AT 502B PT 6-15 Sold
Air Tractor 402 PT-6-20 Sold
EAA Flight Advisor/CFI/Tech Counselor
Louisville, Ga

It's never skill or craftsmanship that completes airplanes, it's the will to do so,
Patrick Kenny, EAA 275132


Dues gladly paid!
Reply With Quote
  #5  
Old 03-23-2008, 10:10 PM
jimski9's Avatar
jimski9 jimski9 is offline
 
Join Date: Apr 2006
Location: Tauranga, New Zealand
Posts: 27
Default

Pierre or Dave

I have a Catto three-blade prop and have cut a longer slot in my 7A lower cowl. However I don't think it is long enough yet.
Can you, or someone else with this set-up measure how long a slot you made to allow easy removal of the lower cowl?

Thanks

Jim Talbot
7A
New Zealand
Reply With Quote
  #6  
Old 03-24-2008, 05:18 AM
db1yg's Avatar
db1yg db1yg is offline
 
Join Date: Mar 2006
Posts: 629
Default

Hi Jim,

I will be out at the hangar later today and will measure the distance from the nose gear leg to the forward most point on the slot--is that what you need??

Cheers,

db
__________________
Dave B.
RV9a/ECiIO360/James Cowl/WW RV200 Prop
Flying since 3/06 and still smiling!!!
Reply With Quote
  #7  
Old 03-24-2008, 11:23 AM
db1yg's Avatar
db1yg db1yg is offline
 
Join Date: Mar 2006
Posts: 629
Default

Jim,

Just got back from the hangar. It looks like mine is between 7.5 and 8.0 inches from the front of the gear leg where it exits the bottom of the cowl to the forward most part of the slot. I have the FairingsEtc intersection fairing that I cut and glassed so it extends forward sufficient to cover the extended slot.

Please note that I have the James cowl which is slightly longer than Vans stock unit--don't think this would matter but .....??? I arrived at this dimension by cutting forward a little at a time until I was satisfied that I had the shortest slot that allowed bottom cowl removal.

Regardless, as has been mentioned, you need to protect the 3 blade composite prop when you remove the bottom cowl.

Hope this helps!

Cheers,

db
__________________
Dave B.
RV9a/ECiIO360/James Cowl/WW RV200 Prop
Flying since 3/06 and still smiling!!!
Reply With Quote
  #8  
Old 03-24-2008, 01:22 PM
jimski9's Avatar
jimski9 jimski9 is offline
 
Join Date: Apr 2006
Location: Tauranga, New Zealand
Posts: 27
Default

Thanks Dave

I will lengthen the slot in my cowl some more.
I think the most important thing Pierre and you have said is to duct-tape the prop before fitting or removing the lower cowl.
I would hate to scratch my new prop before I have even flown!

Cheers

Jim
Reply With Quote
  #9  
Old 01-23-2010, 11:55 AM
RickWoodall's Avatar
RickWoodall RickWoodall is offline
 
Join Date: Jan 2007
Location: Ontario Canada
Posts: 1,452
Default cowl fitting tips for 3 blade install

I read in the archives that the rvator had an article on cowl fitting tips for three blade installs. Cant find it after much digging. Anyone recall how long ago, date of that article etc?
__________________
Rick Woodall C-GSTT "ghost"
9a -TMX io-320, catto three blade, dual dynon hdx with a/p. 900+ hrs in 8 yrs flying.

Flew to Osh 11,12,15,17,19. SNF 2013. West to Cali /Washington/Vancouver/crossed the Rockies north to Red Deer east to Moosonee and over to maritimes. South to Jekyll Isl, cedar key, and Key West etc. 6 trips and 17 islands of the Bahamas. Flown turtles and dogs for Pilots n Paws too. Love our Rv's
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 05:36 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.