VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 11-18-2019, 01:46 PM
rvator9a rvator9a is offline
 
Join Date: Jan 2005
Location: Cape Elizabeth ME
Posts: 139
Default Removing the wings from A model

Im getting to the point where I am going to paint my 9a. I remember how much of a pain it was to install the wing bolts but I am not sure if it is worse to remove them. I have access to an automotive paint booth that would allow me to do a nice clean coat of paint but I would need the wings removed. I could make up a booth in the hangar Im in, but that will entail quite a bit of work to set up a not optimal spray booth. I am curious if anyone has removed the wings and how bad was the project? I am an automotive dealership tech so Im used to dealing with hard to access nuts and bolts, but Im concerned that there is something in the process that could be damaged.
__________________
Bob Collins (the other Bob Collins)
Reply With Quote
  #2  
Old 11-18-2019, 02:08 PM
Robin8er Robin8er is offline
 
Join Date: Sep 2015
Location: Socal
Posts: 453
Default

I had to pull the wings off my 8 for shipping. It's about a 2 day event. It's not too terrible if you have some saw horses cut to the right height and someone to help. The hard part might be electrical wires depending on if they are hard wired or have connectors. I got my wing bolts out with a brass punch to carefully drive them out. Once you get a few out, replace them with hardware store bolts to allow you get the rest of the bolts out without the wing falling. It helps if you take the bolt off the gas tank and rear spar first.

It's a very uncomfortable thing to do. Between the bolts and fuel line fitting it's not much fun at all. There is probably a little more room in your plane than in my 8, but that probably doesnt much it much easier.

I would vote for leaving the wings on. I think it's easier to set up a paint booth in a hanger. Less to go wrong that way.
__________________
RV-8 N695RA flying
Working on an RV-4

Born to fly, forced to work

Last edited by Robin8er : 11-18-2019 at 02:50 PM.
Reply With Quote
  #3  
Old 11-18-2019, 02:33 PM
airguy's Avatar
airguy airguy is offline
 
Join Date: Oct 2006
Location: Garden City, Tx
Posts: 5,147
Default

I've pulled the wings once, and built a paintbooth once. I would definitely build the paintbooth.
__________________
Greg Niehues - SEL, IFR, Repairman Cert.
Garden City, TX VAF 2020 dues paid
N16GN flying 700 hrs and counting; IO360, SDS, WWRV200, Dynon HDX, 430W
Built an off-plan RV9A with too much fuel and too much HP. Should drop dead any minute now.
Reply With Quote
  #4  
Old 11-18-2019, 02:52 PM
rockwoodrv9 rockwoodrv9 is offline
 
Join Date: Dec 2011
Location: Meridian ID, Aspen CO, Okemos MI
Posts: 2,645
Default

It could be done, but wow, what a job. I would rather build a booth around the wings than take them off. I remember gluing bolts to popsicle sticks to get them installed. The wiring and pitot plumbing would be an issue too.

It could be done but I dont see any time savings over a new paint booth. It would be really nice having a real paint booth but it will be difficult transporting parts to and from the paint booth. It would be easy to damage or scratch.

Good luck. Im interested in your decision!
__________________
rockwoodrv9a
Williamston MI
O-320 D2A
Awaiting DAR Inspection
Reply With Quote
  #5  
Old 11-19-2019, 11:49 AM
Jerry Kinman Jerry Kinman is offline
 
Join Date: Jan 2005
Location: Fort Worth area
Posts: 97
Default Build the Paint Booth

I had to experience the agony of removing wings from a partially completed 9A to haul it to my hangar. Reinstalling them was equally difficult.

Some automotive paint booths may not be wide enough to accommodate the 10.5 ft tail span of the RV9. I needed a wide load permit to trailer my project home.
__________________
RV-8 N88GK Sold
RV-9A Slider, N188GK Project, now flying, O-320-B1A, Catto 3 Blade NLE, G3X Touch System
Restored Taylorcraft BC12-65
Exempt but proud contributor
Jerry Kinman, VAF 170
Keller, TX (T67)
Reply With Quote
  #6  
Old 11-19-2019, 12:01 PM
622BH 622BH is offline
 
Join Date: Nov 2011
Location: Albany, OR
Posts: 146
Default Build the Paintbooth

I had a number of painters tell me they would not paint the plane unless I removed the wings.

NOPE!! They were a B....H getting them mounted and I'll be Da.....d if I'll go through the hassle of taking them off.

Nicely enough, John Stahr agreed to paint the plane with the wings mounted. His one condition was I had to have a good quality creeper so he could easily get under the plane, and if necessary had the ability to elevate the plane so he could more effectively paint (less pain for him holding the gun).

Ended up not needing to elevate the plane and the results were fantastic. If the painter knows his / her stuff, it shouldn't be necessary to remove the wings and the quality of the paint booth does not need to be extreme - unless you have DEQ inspectors coming to your hangar.

BUILD THE BOOTH IN YOUR HANGAR - You'll be thankful for not having to remove those wings!
Reply With Quote
  #7  
Old 11-19-2019, 04:56 PM
Ralph Inkster Ralph Inkster is offline
 
Join Date: Feb 2008
Location: Calgary, Alberta
Posts: 1,005
Default

On removing the wings from a 9A or 7A

If you threw a coin in a jar for every cuss word uttered during the wing removal process, you will have a full bucket worth.
__________________
Ralph
built a few RVs, rebuilt a few more, hot rodded some, & maintained/updated a bunch more
Reply With Quote
  #8  
Old 11-19-2019, 09:24 PM
lr172 lr172 is online now
 
Join Date: Oct 2013
Location: Schaumburg, IL
Posts: 5,298
Default

Quote:
Originally Posted by Ralph Inkster View Post
On removing the wings from a 9A or 7A

If you threw a coin in a jar for every cuss word uttered during the wing removal process, you will have a full bucket worth.
Having painted two planes in the garage and one using a creeper, I can tell you there will be just as full of a cuss jar from the experience, especially during the winter in Maine.

Don't forget that a home made booth will likely not keep all the dust down and will require cut and buff.

Larry
__________________
N64LR - RV-6A / IO-320, Flying as of 8/2015
N11LR - RV-10, Flying as of 12/2019
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 08:12 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.