|
-
POSTING RULES

-
Donate yearly (please).
-
Advertise in here!
-
Today's Posts
|
Insert Pics
|

11-23-2018, 04:29 PM
|
|
|
|
Join Date: Oct 2018
Location: Mission Viejo, CA
Posts: 8
|
|
Blind vs Solid Rivet
Hi All,
I am about 15 hours deep into the empennage kit and just starting to get to permanent rivets. Are the solid rivets stronger than the blind rivets? Some spots seem much easier to blind rivet, but the directions say to use a solid rivet.
|

11-23-2018, 06:31 PM
|
 |
|
|
Join Date: Oct 2005
Location: Estes Park, CO
Posts: 3,947
|
|
Cherrymax
I didn't stay in Holiday Inn so take this for what it's worth.
Always follow Van's design. They have the FEA to know what changes can be used.
Only one pop rivet is as strong as a solid rivet. Cherrymax.
That said, Vans does allow a pop rivet in some places like the last hole at the trailing edge.
__________________
Larry Larson
Estes Park, CO
http://wirejockrv7a.blogspot.com
wirejock at yahoo dot com
Donated 12/03/2019, plus a little extra.
RV-7A #73391, N511RV reserved (2,000+ hours)
HS SB, empennage, tanks, wings, fuse, working finishing kit
Disclaimer
I cannot be, nor will I be, held responsible if you try to do the same things I do and it does not work and/or causes you loss, injury, or even death in the process.
|

11-23-2018, 06:31 PM
|
|
|
|
Join Date: May 2006
Location: Pocahontas MS
Posts: 3,884
|
|
For structure, regular pulled rivets can't replace solid fivets. Only Cherrymax can typically replace solid rivets, and not in every hole of a line of rivets.
|

11-23-2018, 07:51 PM
|
|
|
|
Join Date: Jun 2011
Location: Nashua, NH
Posts: 536
|
|
On the RV-4, it was allowed to substitute the 3/32” solid shank rivet with a CS4-4 pulled rivet on the bottom wing skins. It was said to be 10% stronger because of the larger size. The finish wouldn’t be as smooth though.
__________________
Mike
RV-4 #2750
N654ML
IO-360
WW150C Prop
1018 lbs
Flying
|

11-24-2018, 08:08 AM
|
 |
|
|
Join Date: Dec 2016
Location: New Braunfels
Posts: 299
|
|
Quote:
Originally Posted by Michael Henning
On the RV-4, it was allowed to substitute the 3/32? solid shank rivet with a CS4-4 pulled rivet on the bottom wing skins. It was said to be 10% stronger because of the larger size. The finish wouldn?t be as smooth though.
|
Thought I'd try this on a 3/32" dimpled hole in a test piece just to see how proud it would sit. Was AMAZED at how flush a CS4-4 would sit in a 3/32" dimple. It may not be perfect, but once primed and painted, bet you can't tell the difference. Sometimes the simplest of things elude me until someone post something like this and you have an "ah-ha" moment. Thanks Michael!
__________________
Randy Vanstory
Flying RV10 - N783V
1st Flight 08/20/2020
Donation Happily Made 2020
|

11-24-2018, 08:53 AM
|
 |
|
|
Join Date: Jan 2005
Location: 57AZ - NW Tucson area
Posts: 10,011
|
|
Quote:
Originally Posted by Michael Henning
On the RV-4, it was allowed to substitute the 3/32? solid shank rivet with a CS4-4 pulled rivet on the bottom wing skins. It was said to be 10% stronger because of the larger size. The finish wouldn?t be as smooth though.
|
IIRC it was allowed to use the smaller MK319BS rivet which needed a 7/64 hole rather than a CS-4-4 rivet in a 1/8 hole.
Given that nothing was pre-punched in those olden days the larger 1/8 holes could start getting into edge distance issues.  The early instructions allowed that on the whole wing.
__________________
Gil Alexander
EAA Technical Counselor, Airframe Mechanic
Half completed RV-10 QB purchased
RV-6A N61GX - finally flying
Grumman Tiger N12GA - flying
La Cholla Airpark (57AZ) Tucson AZ
|

11-25-2018, 09:35 AM
|
|
|
|
Join Date: Jun 2011
Location: Nashua, NH
Posts: 536
|
|
I would use an 1/8” hole, and appropriate dimple die, it will sit even nicer.
__________________
Mike
RV-4 #2750
N654ML
IO-360
WW150C Prop
1018 lbs
Flying
|

12-12-2018, 11:06 PM
|
|
|
|
Join Date: Aug 2014
Location: Edmonton, AB
Posts: 216
|
|
There is going to be a few more places in the future where you may consider a pulled rivet. On the wings, you may choose to use pulled rivets attaching the leading edge to the spar. I've had to use a couple for the wing skin and rear spar where the new aileron doubler gets installed. I've also used one inside the fuel tank. Wirejock is right cherrymax are very strong. You would be wise to read up eventually on pulled rivet types. I did up a solid/pulled rivet comparison spreadsheet that listed all the shear strength, grip length and rivet/pin material. I also bought 1-2 cherry max rivets of each size and length. This became extremely handy for the handful of times you will run into a snag and didn't break the bank.
I always emailed Vans to double check if a particular pulled rivet type was acceptable for the area I was working on and that quick reply went in my build binder.
Last edited by Aero_Octaveus : 12-12-2018 at 11:09 PM.
|

12-13-2018, 08:54 AM
|
|
|
|
Join Date: Dec 2009
Location: Boulder, CO
Posts: 4,436
|
|
I have no data for the NAS1097 rivets, but seriously doubt that they are as strong as the rivets we use elsewhere. The body is, but since the heads are smaller, they'd pull through with a serious shear load.
For the standard rivets, twice as many -3 rivets on 1" spacing are slightly stronger than -4 rivets on 2" spacing.
Dave
|

12-13-2018, 08:56 PM
|
|
|
|
Join Date: Jul 2018
Location: Naples fl
Posts: 140
|
|
Quote:
Originally Posted by David Paule
I have no data for the NAS1097 rivets, but seriously doubt that they are as strong as the rivets we use elsewhere. The body is, but since the heads are smaller, they'd pull through with a serious shear load.
For the standard rivets, twice as many -3 rivets on 1" spacing are slightly stronger than -4 rivets on 2" spacing.
Dave
|
NAS1097 rivets are commonly used by Boeing on skins. Some of the fuselage skins are .080" thick.
The problem with using a cherry max besides the cost is that the stem and lock ring are steel, the body is aluminum. Differential metal corrosion. I worked on twin otters on floats in the Caribbean and the cherry rivets would only have the body remaining, everything else disappeared.
Also if you never had to remove a cherry you're in for a experience. That stem and ring are hard. We used a high speed grinder and a tiny ball rotary file to get the ring out. One slip and you screw up a skin.
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 09:14 AM.
|