VansAirForceForums  
Home > VansAirForceForums

- POSTING RULES
- Donate yearly (please).
- Advertise in here!

- Today's Posts | Insert Pics

  #1  
Old 07-20-2016, 09:39 AM
SuperCubDriver SuperCubDriver is offline
 
Join Date: Feb 2011
Location: Germany
Posts: 443
Default Need help with engine adjustments

I just completed my RV-8 - posted in another thread.
The airplane has a AerosportPower IO-375M1S low compression with 2 P-Mags, Superior sump and Airflow Performance FM-150 Fuel Injection System with purge valve.

I?m having two issues and looking for help and advise:

1. Idle quality is lousy, RPM is fluctuating. When advancing the throttle engine smoothes out at about 1400 RPM. Leaned the idle with the adjuster screw on the throttle body with no help. mixture lever is almost unresponsive. Checked for intake leaks visually, all bolts are secure and no visible gap. Boost pump on or off doesn?t matter, fuel pressure without boost pump is around 15-27 psi, with boost pump on 35 psi.
Is there a good and simple way to check for intake leaks?
I did not touch the ignition yet but left, right or both mags is just the same.

2. When advancing the throttle without the boost pump at around 2000 RPM the fuel pressure is going down to 5 psi followed by decreasing fuel flow, so the engine does not power up with only the engine driven pump. It accelerates fine with good power for a very short time til the fuel flow drops.
With boost pump on it accelerates normal with normal power output (FF 16 GPH). I once disconnected the engine driven pump and operated the engine with only the boost pump. Idle problem is still present then and the engine is powering up.

So if anyone had a similar experience or ideas how to approach these problems I am very interested in getting directions.

Thanks - Hermann
__________________
RV-7 flying, IO-375 w. P-Mags, 200RV Prop

RV-8 flying, IO-375, P-Mags, 74RV Prop
Reply With Quote
  #2  
Old 07-20-2016, 12:06 PM
BillL BillL is offline
 
Join Date: Sep 2007
Location: Central IL
Posts: 5,516
Default

Quote:
Originally Posted by SuperCubDriver View Post
I just completed my RV-8 - posted in another thread.
The airplane has a AerosportPower IO-375M1S low compression with 2 P-Mags, Superior sump and Airflow Performance FM-150 Fuel Injection System with purge valve.

I?m having two issues and looking for help and advise:

1. Idle quality is lousy, RPM is fluctuating. When advancing the throttle engine smoothes out at about 1400 RPM. Leaned the idle with the adjuster screw on the throttle body with no help. mixture lever is almost unresponsive. Checked for intake leaks visually, all bolts are secure and no visible gap. Boost pump on or off doesn?t matter, fuel pressure without boost pump is around 15-27 psi, with boost pump on 35 psi.
Is there a good and simple way to check for intake leaks?
I did not touch the ignition yet but left, right or both mags is just the same.

2. When advancing the throttle without the boost pump at around 2000 RPM the fuel pressure is going down to 5 psi followed by decreasing fuel flow, so the engine does not power up with only the engine driven pump. It accelerates fine with good power for a very short time til the fuel flow drops.
With boost pump on it accelerates normal with normal power output (FF 16 GPH). I once disconnected the engine driven pump and operated the engine with only the boost pump. Idle problem is still present then and the engine is powering up.

So if anyone had a similar experience or ideas how to approach these problems I am very interested in getting directions.

Thanks - Hermann
Without doing research on what you have, the engine pump should provide a lot more than 5 psi for the FI system. Look at the specs, it will tell you the minimum fuel pressure. If the pump does not provide that, then it is defective, or it is an incorrect pump (maybe for a carb engine).

Once that is addressed, then it will be appropriate to look at the idle symptoms.

BTW - you should be wary of flying this airplane with a bad mechanical pump.
__________________
Bill

RV-7
Lord Kelvin:
“I often say that when you can measure what you are speaking about,
and express it in numbers, you know something about it; but when you
cannot measure it, when you cannot express it in numbers, your knowledge
is of a meager and unsatisfactory kind.”
Reply With Quote
  #3  
Old 07-20-2016, 02:02 PM
jrs14855 jrs14855 is offline
 
Join Date: Apr 2008
Location: Lake Havasu City AZ
Posts: 2,393
Default Fuel Pressure

If you have the standard AC style engine driven fuel pump, what kind of fittings do you have at the pump.
Many Pipers and IIRC all factory built Pitts aircraft use an AN bulkhead fitting, with jam nut and a special o ring. There have been a number of cases on RV's and Rockets where these fittings were improperly installed and/or improperly torqued. The o ring style fitting is very critical, if under torqued it will leak, if over torqued the o ring may be damaged. What is the history of the fuel hoses? If they were not fabricated and tested in a hose shop there is always the possibility of a defect in the hose inner lining, usually a flap of rubber that is not easily seen when looking at the hose visually.
Was the engine test stand run by the engine builder? If it has some test stand time you could probably get away with aggressively leaning the engine with mixture control for all ground operations. My experience is only with the Bendix system but these engines tend to run very erratically on the ground at low r/m. Leaning aggressively for all ground operations helps.
The fuel pressure/fuel flow issue does need to be addressed before flight.
Reply With Quote
  #4  
Old 07-20-2016, 02:08 PM
jrs14855 jrs14855 is offline
 
Join Date: Apr 2008
Location: Lake Havasu City AZ
Posts: 2,393
Default Fuel Pump Fittings

The fittings as used on Pitts and many Pipers with Lycoming engine is AN833-6 elbow with long end screwed into pump. AN 924-6 jam nut. O ring that I have always used is a Piper part number.
Vans may call for something different.
Reply With Quote
  #5  
Old 07-20-2016, 03:57 PM
SuperCubDriver SuperCubDriver is offline
 
Join Date: Feb 2011
Location: Germany
Posts: 443
Default

No way I fly without engine running on the engine driven pump only.
Pump is LW-15473 high pressure diaphragm pump, at least on the papers, how can I check the pumpo is the right one?
It has the fittings with the o-rings and I did a flow test with the boost pump. At least with the boost pump is more than 200% flow of maximum flow required (through the engine driven pump). The hoses are teflon/new and I doubt there are things like rubber flaps inside, I blowed them through prior installation but will check again. Up to the firewall I?m having aluminum tubing.
Note that the engine driven pump is providing around 25psi pressure but not with the higher fuel flow. I am also thinking of some restriction before the pump but I also think this is unlikely. I checked the fuel filter which was very clean, also the inlet filter in the FM-150 is clean.

The engine was test run by the engine builder but I?m not sure they used the now installed equipment for their runs. So for example the oil pressure was way low and on the test sheet in the upper half of specifications. I also checked the oil pressure with a second gauge. That makes me feel that I have to start from the very beginning.
__________________
RV-7 flying, IO-375 w. P-Mags, 200RV Prop

RV-8 flying, IO-375, P-Mags, 74RV Prop
Reply With Quote
  #6  
Old 07-20-2016, 05:09 PM
AltonD's Avatar
AltonD AltonD is offline
 
Join Date: Sep 2005
Location: Dothan, Alabama
Posts: 1,487
Default

With the engine idling, what does the rpm indication do as you slowly pull the mixture to idle cut off? You should see 50-100 rpm increase (running a tad rich).
__________________
Alton DeWeese
N526RV RV7A Tip Up, IO360 180 W/Hartzel BA prop.
Flying ~950 hours since Aug 2010
N4IDH

Construction Log
?The secret of getting ahead is getting started. The secret of getting started is breaking your complex overwhelming tasks into small manageable tasks, and then starting on the first one.?

?Mark Twain
Reply With Quote
  #7  
Old 07-20-2016, 07:44 PM
TylerII TylerII is offline
 
Join Date: Jun 2010
Location: Easley, SC
Posts: 40
Default IO375 timing is different

did you retime the Pmags. The timing is different on the IO375 from the usual 25 degrees. We had the same issue on a re-install after upset landing prop strike cause a change from IO360 180 to IO 375. Once thePmags were timed right the engine ran great.
Just a suggestion something to check
Tyler
A&P, EAA Tech advisor
RV7A Builder
Reply With Quote
  #8  
Old 07-20-2016, 07:52 PM
jrs14855 jrs14855 is offline
 
Join Date: Apr 2008
Location: Lake Havasu City AZ
Posts: 2,393
Default Pump

LW15473 Is the correct pump. The pictures in Spruce catalog show the part number stamped close to the mounting flange on the left side, the part number is shown vertical with the LW at the top. You can view this at aircraftspruce.com, search Lycoming fuel pump, click on the image to enlarge it.
Another remote possibility if the fuel pump was removed and reinstalled after the engine runs is the possibility that the actuator rod is not properly aligned and making contact with the arm of the fuel pump. Very unlikely but it has happened.
I have no experience with the purge valve system but an easy check would be to simply cap off the line to the purge valve and do a test run. An alternative is to disconnect the line between the purge valve and the tank, stick the line in a can and run the boost pump.
You could also run a line from a gas can direct to the engine driven pump for testing. Starting would require cranking the engine a bit with the mixture full rich to prime, then normal starting procedure.
Most of the above very unlikely but possible. Verify the pump part number first.
Reply With Quote
  #9  
Old 07-20-2016, 07:53 PM
jrs14855 jrs14855 is offline
 
Join Date: Apr 2008
Location: Lake Havasu City AZ
Posts: 2,393
Default Pump

Forgot to mention the proper Tempest pump is AF15473
Reply With Quote
  #10  
Old 07-20-2016, 08:10 PM
jrs14855 jrs14855 is offline
 
Join Date: Apr 2008
Location: Lake Havasu City AZ
Posts: 2,393
Default Pumps

Just as a reference point the majority of the early Pitts S1 aircraft including the first few factory S1's used the Bendix PS5C carb. This was supported by a medium pressure engine driven pump which is no longer available new. Backup pump was a hand wobble pump. These airplanes flew thousands of hours on just the engine driven pump. The wobble pump was used for priming and as a backup in case of engine driven pump failure.
Your engine should run perfectly on just the engine driven pump, although you will have the typical low power roughness associated with the fuel injection.
I have 1000 hours plus on just the engine driven pump, never the slightest problem unless I ran a tank dry.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 01:34 AM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.