|
-
POSTING RULES

-
Donate yearly (please).
-
Advertise in here!
-
Today's Posts
|
Insert Pics
|

02-25-2016, 03:01 PM
|
|
|
|
Join Date: Mar 2009
Location: Arvada, CO
Posts: 118
|
|
You might consider repositioning the entry air ramp on the top cowl. I had very similar CHT problems until I moved mine forward. This really improved entry air volume and greatly reduced temps, especially #1. Just search this forum for more detail. Worked great for mr, FP 0-360, RV7. Easy fix!
Good luck, Jim
|

02-25-2016, 03:13 PM
|
 |
|
|
Join Date: May 2005
Location: X35 - Ocala, FL
Posts: 3,679
|
|
Quote:
Originally Posted by bluebrear
Vern, Speaking with Marvel-Shleber, I found out that my carb has one of the richest jets installed. It starts out at .101" dia. Do you have any idea how much increase in the bore would be to attain?
|
Are you absolutely sure you're hitting the rich stop on the mixture?
__________________
Jesse Saint
|

02-25-2016, 03:13 PM
|
|
|
|
Join Date: Oct 2005
Location: Geneva, AL
Posts: 491
|
|
Drill
When I did mine I drilled it in steps and ended up at a #39 drill. 0.995. That took mine from a rich to peak increase of about 50 degrees to 175 degrees and helped the cooling a lot in the climb. I would think that if yours is in fact .101 now that the problem would be more in the baffling and timing.
Even after drilling out, if I climb at VX very long i will shoot past 400. I try to climb at nothing less than 100 knots unless it's necessary.
Mine does have 9:1 pistons in it also.
Someone mentioned the ramp on the inside of the cowl and I truly believe that this is an area that would really help the cooling. DanH and I have talked about it several times and he's posted about it also. I will change mine at condition inspection time just to see what difference it makes.
__________________
Paul Rose
RV-9A 91300
N417PR
SERFI 2013 Awards
Inspection Complete!!! 7/7/12
First Flight 7/22/12
|

02-26-2016, 10:33 AM
|
|
|
|
Join Date: Feb 2013
Location: Bethel
Posts: 32
|
|
Jim
Did you cut the dam out, shorten it and then replace a shorter section, thus moving that dam forward? If so, about how much forward?
Thanks
|

02-26-2016, 11:08 AM
|
|
|
|
Join Date: Feb 2013
Location: Bethel
Posts: 32
|
|
Would like some opinions about ambient temps affecting the CHT's. We're flying in Maine winter with these high CHT temps and concerned about increasing OAT's as the WX improves.
|

02-26-2016, 11:20 AM
|
|
|
|
Join Date: Aug 2005
Location: Atlanta, GA
Posts: 4,219
|
|
My CHT's in cruise are typically ambient + ~280F.
__________________
Kyle Boatright
Marietta, GA
2001 RV-6 N46KB
2019(?) RV-10
|

02-26-2016, 02:34 PM
|
|
|
|
Join Date: Jan 2005
Posts: 3,646
|
|
I would say mine are pretty similar to Kyle's: ambient + ~280F will be my average across all 4 CHTs, though I'm usually running only 65% power when I'm economy cruising. I'm assuming they'd be higher if I try to cruise faster. In addition, if my oil gets really warm because it's a hot day, I think my CHT's will rise a bit beyond what the above formula above suggests. I'm still fighting some cooling issues I think, though I'm gradually finding baffeling improvements to help.
__________________
Steve M.
Ellensburg WA
RV-9 Flying, 0-320, Catto
Donation reminder: Jan. 2021
|

02-27-2016, 05:37 PM
|
|
|
|
Join Date: Mar 2009
Location: Arvada, CO
Posts: 118
|
|
Yep, I just used my Dremel to cut the ramp out, smoothed things up a bit, shortened it about an inch and a half as I recal, then glassed it back in. They say you should be able to make a fist and shove in through between the ramp and the cylinder. I'm there now. It was easy.
Jim
|

02-28-2016, 04:10 AM
|
|
Super Moderator
|
|
Join Date: May 2005
Location: Locust Grove, GA
Posts: 2,627
|
|
Here's a reason
In an RV-9A I looked at yesterday the CHT probe was installed in the PRIMER port of the number 3 cylinder! That's a first.
Vic
__________________
 Vic Syracuse
Built RV-4, RV-6, 2-RV-10's, RV-7A, RV-8, Prescott Pusher, Kitfox Model II, Kitfox Speedster, Kitfox 7 Super Sport, Just Superstol, DAR, A&P/IA, EAA Tech Counselor/Flight Advisor, CFII-ASMEL/ASES
Kitplanes "Unairworthy" monthly feature
EAA Sport Aviation "Checkpoints" column
EAA Homebuilt Council Chair/member EAA BOD
Author "Pre-Buy Guide for Amateur-Built Aircraft"
www.Baselegaviation.com
|

02-28-2016, 05:34 AM
|
 |
|
|
Join Date: May 2005
Location: X35 - Ocala, FL
Posts: 3,679
|
|
Quote:
Originally Posted by vic syracuse
In an RV-9A I looked at yesterday the CHT probe was installed in the PRIMER port of the number 3 cylinder! That's a first.
Vic
|
That's scary. That's an NPT thread port. Most CHT probes are strait threads, aren't they?
__________________
Jesse Saint
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 08:09 AM.
|