VAF Forums

VAF Forums (https://vansairforce.net/community/index.php)
-   RV General Discussion/News (https://vansairforce.net/community/forumdisplay.php?f=2)
-   -   Oil filter question (https://vansairforce.net/community/showthread.php?t=158911)

Charles in SC 03-23-2018 01:00 PM

Oil filter question
 
While trying to hook up the lines to my oil cooler I gave up and decided to pull the oil filter off so I would have more working room. Great but when I tried to unscrew it it would not budge. Yes I took the safety wire off. It is so tight that I destroyed an oil filter wrench trying to get it off. This is a factory new engine. I am no stranger to stuck filters after having owned heavy equipment and big trucks for years. I just wondered if there were any tips to know before I put the big cheater on it.
Thanks

Whitman 03-23-2018 01:14 PM

Tap a flat head screw driver through the side of it, then you'll have a built in handle and plenty of leverage to get it off. I know most people don't, but this is why I'm a big fan of torqueing the filter on to the proper TQ spec.

Raymo 03-23-2018 01:55 PM

It is likely the seal that is stuck. Some use engine oil to lubricate it prior to installation. DC4 works better or the new Tempest filters that have lube impregnated into the seal.

I have a large pair of channel lock pliers as my cheater :D

BillL 03-23-2018 03:21 PM

Quote:

Originally Posted by Charles in SC (Post 1248124)
While trying to hook up the lines to my oil cooler I gave up and decided to pull the oil filter off so I would have more working room. Great but when I tried to unscrew it it would not budge. Yes I took the safety wire off. It is so tight that I destroyed an oil filter wrench trying to get it off. This is a factory new engine. I am no stranger to stuck filters after having owned heavy equipment and big trucks for years. I just wondered if there were any tips to know before I put the big cheater on it.
Thanks

I just removed my original filter and it was gawd-awful tight. I used a 1"box end wrench and it came off. Driving a screw driver through it will just shear the can, and not generate more torque than a wrench. Be sure to use a new gasket when you reassemble.

Now I have to make an offset wrench to torque with more confidence.

RV7A Flyer 03-23-2018 04:11 PM

And use one of these next time...

http://www.aircraftspruce.com/catalo...clickkey=76844

Mel 03-23-2018 04:35 PM

When I have this type of problem I usually have best luck with a strap wrench. These get a grip on a large portion of the filter housing.

KRviator 03-23-2018 05:07 PM

Quote:

Originally Posted by Mel (Post 1248161)
When I have this type of problem I usually have best luck with a strap wrench. These get a grip on a large portion of the filter housing.

Me too. I didn't even notice the filter had a hex nut on it! :D

This is what I use for any oil filter I install or remove, on any vehicle.

Charles in SC 03-25-2018 10:12 AM

Thanks for the help everyone, I got the filter off. Now the next question. Is the threaded nipple supposed to stay in the engine? Mine came off with the filter.
Thanks!

Sam Buchanan 03-25-2018 11:04 AM

Quote:

Originally Posted by Charles in SC (Post 1248468)
Thanks for the help everyone, I got the filter off. Now the next question. Is the threaded nipple supposed to stay in the engine? Mine came off with the filter.
Thanks!

You didn't tell us the type of filter but if it is the common 48110 the nipple is part of the filter.

Charles in SC 03-25-2018 06:08 PM

Thanks, I found that too. I guess it kind of scared me when I saw the nipple. I had not run into this in my past experience.


All times are GMT -6. The time now is 01:07 PM.