VAF Forums

VAF Forums (https://vansairforce.net/community/index.php)
-   RV-12/RV-12iS (https://vansairforce.net/community/forumdisplay.php?f=73)
-   -   SB 18-02-02 Potential cracking in the horizontal stabilator front spar (https://vansairforce.net/community/showthread.php?t=157839)

John C 02-24-2018 10:38 AM

I used the Magnaflux Spot Check. It was $80-90 from Zoro, free shipping, no tax. They said a week or two for shipping, but it came in 4 days from Texas to Kansas, UPS.

TomVal 02-24-2018 01:36 PM

Quote:

Originally Posted by John C (Post 1241801)
I used the Magnaflux Spot Check. It was $80-90 from Zoro, free shipping, no tax. They said a week or two for shipping, but it came in 4 days from Texas to Kansas, UPS.

Thanks John.

RFSchaller 02-24-2018 10:20 PM

I?m not going to bother with looking for racks, just install the fix. If you find cracks the solution is the fix, so what?s the point in inspecting if you just put in the mod?

KALEWIS 02-24-2018 10:52 PM

You would need to stop drill any cracks ......

RFSchaller 02-26-2018 09:08 PM

Oops, sorry, I meant that post to be on the HS spar crack mod thread. Senior moment, I guess!

funflying 03-01-2018 07:50 PM

Post #59
 
So sorry for some mis-information reference the clips for the turnbuckles. These clips are not in the SB18-02-02 parts. It was actually 2 cotter pins with also have an MS##### similar to the clips.

Bottom line....no clips so if you anticipate re-adjusting the turnbuckles order additional clips.

Mitch757 03-01-2018 08:59 PM

I got 2 clips and cotter pins with my kit.

Mitch Garner
RV12 flying year 3

Jim T 03-01-2018 09:12 PM

Quote:

Originally Posted by Mitch757 (Post 1243152)
I got 2 clips and cotter pins with my kit.

Mitch Garner
RV12 flying year 3

Same for me.

Slane 03-01-2018 10:04 PM

Quote:

Originally Posted by Mitch757 (Post 1243152)
I got 2 clips and cotter pins with my kit.

Mitch Garner
RV12 flying year 3

I had ordered the SB package earlier and picked it up today. Two cotter pins and nso cable clips. Vans is out of these clips and so they’re now on ‘back order’. Could be a long wait so I was advised to locate clips from another vendor.

On another SB note, is there something special about the aviation penetration dye that is lacking in more common penetration dye kits available at the auto parts store? What are people using and where have they purchased it?

Thanks for info.

Skunkworks 03-02-2018 07:12 AM

Jane is having major surgery SB 18-02-02 the elevator.
 
Jane is very fortunate in that she is rich with friends that want to help her out.:) This time it was major surgery SB 18-02-02 the elevator.
Dave, friend and A&P mechanic, came over with his specially built table just for the RV-12 fleet.
His table is already reserved for use for another RV-12 at Wings Field.
Certainly made the job a bit easier, just slide it under adjust height to match and we were all set.

Service Bulletin 18-02-02 to address any potential cracking in the horizontal stabilator front spar.
Did not find any cracking on Jane:cool:, however, performed the SB as a prevention measure.

Had to hold for 24 hrs due to finding one of the bearings would slip out of the flange with little pressure.
Put Loctite on it and checked the following day and we were good to go for Elevator installation.

Click on image to see Time Lapse video of the surgery.
]





All times are GMT -6. The time now is 04:47 AM.