VAF Forums

VAF Forums (https://vansairforce.net/community/index.php)
-   RV General Discussion/News (https://vansairforce.net/community/forumdisplay.php?f=2)
-   -   Alodine (https://vansairforce.net/community/showthread.php?t=123114)

Jrskygod 02-23-2015 05:12 PM

Alodine
 
Does Alodine have a shelf life? Does it stop working if several years old?

gasman 02-23-2015 06:17 PM

I find, the older it is..... the longer it takes to work.

JanRV6UK 02-23-2015 06:22 PM

Are you asking about mixed Alodine or just the powder before mixing it ?
For what it’s worth – I had some 10 year old mixed stuff – about 5 liters – It was kept in a sealed plastic container – It still had a good nice golden tint – All I did was to shake the mixture about before pouring it out in my dip tank. Put a few Alu parts in … 3 to 5 min later .. came out with a nice light golden tint.
The solution will give of some toxic fumes over time – so I did the work outside – also work better if the mixture is 20Deg C.

BillL 02-23-2015 06:34 PM

Quote:

Originally Posted by gasman (Post 961976)
I find, the older it is..... the longer it takes to work.

Now you are just being harsh, and you don't even know me.:eek:

BillL 02-23-2015 06:42 PM

OK, seriously, to the OP.

I had a gallon that I poured (75%) into some PVC tubes and seal from the air. The 15% went into a clear, but sealed, container but did not get used. The 15% went bad, got dark and would not work over a year, but I used the batch in the PVC tube many many times and slowly diminished in performance. The last 10% in the original container was like new after all that time.

No explanation, but my very limited experience. I mix from powder now.

flyingriki 02-23-2015 06:55 PM

I read it's important to keep it out of the sunlight. Mine is stored in a cabinet rarely opened.

DaveO 02-23-2015 07:01 PM

I put my left over Alodine in the Refrigerator. That kept it out of the sunlight and the cool seemed to make it last for a long time. I don't know the total time it is ongoing. 3+ Yr now.
Dave

TylerII 02-23-2015 07:10 PM

Alodine is extremely toxic
 
The solution will give of some toxic fumes over time ?

Alodine is a combination of Hydrofluoric acid and hexavalent chrome. Hexavalent chrome is a really bad chemical. Remember Pacific Gas and Electric and Erin Brockavich. Be very careful with storage and disposal. Read the MSDS on the material. Do not dispose of it down the drain. You could go to jail for that action.

Just a warning!
Tyler
A&P

Oliver 01-10-2016 08:46 PM

Quote:

Originally Posted by TylerII (Post 961998)
The solution will give of some toxic fumes over time ?

Alodine is a combination of Hydrofluoric acid and hexavalent chrome. Hexavalent chrome is a really bad chemical. Remember Pacific Gas and Electric and Erin Brockavich. Be very careful with storage and disposal. Read the MSDS on the material. Do not dispose of it down the drain. You could go to jail for that action.

Just a warning!
Tyler
A&P

I am aware that this is an older thread and I am also wondering whether I should even publicly ask this question.

Anyway, though, Is there any practical way to collect and dispose the rinse water? These are relatively large amounts, particularly from the rinsing of parts which don't fit into a bucket.

I found this post by an EAA chapter http://www.eaa1000.av.org/technicl/corrosion/more.htm in which they suggest to let the water evaporate and to mix the remaining powder into cement. I guess this works for the original Alodine solution, though probably not so much for contaminated rinse water!?

aerhed 01-10-2016 10:33 PM

Take it to Oklahoma and have it injected? I try to minimize it. The pvc tube for long parts helps a bunch because you conserve. Small parts I put in a ziploc and a minimum splash from the jug. You can slosh it around and watch it. Use it a couple times if you're careful with the bag. I don't really rinse small parts so much. I let them dry and wipe the powder residue off with a damp paper towel after awhile. Then the towels go in the ziploc until the alodine is soaked up. Then I, uh uh..well anyway.


All times are GMT -6. The time now is 02:19 AM.