VAF Forums

VAF Forums (https://vansairforce.net/community/index.php)
-   RV-10 (https://vansairforce.net/community/forumdisplay.php?f=4)
-   -   Custom Panel (https://vansairforce.net/community/showthread.php?t=1161)

dicel87 04-07-2005 07:41 PM

Custom Panel
 
Anyone seen this yet? Awesome custom made RV-10 panel...I think it is very sharp. Wonder if they'll come out with an RV9 or 7 model?

http://www.myrv10.com/miscphotos/Ran...404/index.html

SteinAir 04-08-2005 01:39 PM

While I agree that is a very nice looking ensemble in that RV-10, I'm not sure I'd jump through hoops or my wallet to get one.

There's already more than one avenue for custom molded panels for your RV's (yes, the side by side's as well), and have been for a number of years. They aren't as popular as you'd think for a number of reasons. Foremost has been cost, next has been installation, and then a whole slew of other reasons. There are actually quite a few molded glass panel flying out there in RV's, but if you ask many of the people who did it if they'd do it again, you'll get varied responses.

If I were you, I'd carefully weigh the pro's and con's to these types of panels. Remember, some benefits are only "perceived", while other benefits are real...make sure you can deliniate between the two when choosing. Function and Form almost never go hand in hand (where you desire 100% of either/both). The best is usually a compromise of each.

Just my 2 cents as usual!

Cheers,
Stein.

w1curtis 04-11-2005 12:48 PM

I somewhat agree with Stien on this. While this panel looks awesome, these guys, Aerocraft Parts, are use to selling fully installed and configured panels to the Lanciar crowd for BIG bucks. If they sell just the fiberglass moulding and metal panels without avionics, that may a good start, but I think that will also be expensive.

Will see if I can get some pricing information out of them at Sun-N-Fun.

Air UPSer 04-11-2005 02:59 PM

Quote:

Originally Posted by dicel87
Anyone seen this yet? Awesome custom made RV-10 panel...I think it is very sharp. Wonder if they'll come out with an RV9 or 7 model?

http://www.myrv10.com/miscphotos/Ran...404/index.html

Have you tried contacting the builder of the RV10 you referenced to get his take on the panel?

I'm sure the forum would be interested in first hand info.

Air UPSer

pdecraene7a 04-12-2005 06:30 AM

custom panel
 
Laird Owens makes a very nice composite panel which will fit the 6,7,and 9A.
I used Lairds panel. It was pretty easy to install and if I had left it stock it would have gone together quickly, but I had to make a few modifications and it probably added a couple of weeks to my build time but I am very happy with the end results.

Pete DeCraene
http://www.ews.uiuc.edu/~decraene/index.htm

dicel87 04-12-2005 08:15 PM

Your panel looks great Pete. Very nice job.

RV10Pilot 04-12-2005 09:30 PM

Pete, where did you get the EL panel lighting from.

Larry
RV10 #40356

Quote:

Originally Posted by pdecraene7a
Laird Owens makes a very nice composite panel which will fit the 6,7,and 9A.
I used Lairds panel. It was pretty easy to install and if I had left it stock it would have gone together quickly, but I had to make a few modifications and it probably added a couple of weeks to my build time but I am very happy with the end results.

Pete DeCraene
http://www.ews.uiuc.edu/~decraene/index.htm


pdecraene7a 04-13-2005 06:25 AM

EL Lighting
 
Larry,

My EL came from aircraft extras. It is advertised as being very thin but the end where the wires attached were covered with silicon on the back side and made it difficult to lay flat. It does however make a great light for the panel. I have made several night landings and 1 cross country at night and the panel light is very bright and dims nicely to any level.


http://www.aircraftextras.com/EL-Panel1.htm

Pete DeCraene
N526PD
Leaving for Sun N Fun Thursday

SteinAir 04-13-2005 12:27 PM

Quote:

Originally Posted by pdecraene7a
Larry,

My EL came from aircraft extras. It is advertised as being very thin but the end where the wires attached were covered with silicon on the back side and made it difficult to lay flat. It does however make a great light for the panel. I have made several night landings and 1 cross country at night and the panel light is very bright and dims nicely to any level.


http://www.aircraftextras.com/EL-Panel1.htm

Pete DeCraene
N526PD
Leaving for Sun N Fun Thursday


Not to purposely stump here, but rather to save you money.

I stock the same stuff, only about $30.00 less! (30%). I also have been using these lights for a couple years and have yet to find anything better - just cheaper! In case you're wondering why I can sell them for so much less, it's because I buy them in HUGE lots at a time, and get quite a bit better deal than those guys do on the same lighting.

Just an FYI.

Cheers,
Stein.

P.S., correct about the attached wires, they do stick up a very little bit, probalby about 1/16" inch or less.

w1curtis 04-28-2005 02:25 PM

So I stopped by to see these guys at Sun-N-Fun and get a price out of them. I must say, even though they did not give me a concrete price (they said between $1200- $1700) and really wanted to get the business to build your ENTIRE Panel, I found it promising.

I love the wiring part of my project too much to hand it over to them, but I do think if I can get the panel and pedestal for the low end of that price range, I will get one from them. They were taking $2500 deposits at the show which supposedly would get you the panel for FREE if you had them build you a panel. I guess I still believe that nothing in life is FREE.

http://www.myrv10.com/N104CD/panel/snfpanels/index.html

FYI
They changed their name from Lancair Avionics to Aeroparts exactly because people (like myself) associated Lancair Avionics with $$$Pricey.


All times are GMT -6. The time now is 07:29 AM.